Models > WRT21S4AW3 > Instructions

WRT21S4AW3 Westinghouse Refrigerator - Instructions

All installation instructions for WRT21S4AW3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRT21S4AW3
166-180 of 279
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken crisper tray

  • Customer: robert from edison NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old tray and slid in the new ones

changed defrost timer

  • Customer: Gerry from Apache Jct AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video very esay

Our refrigerator was not cooling below 50 degrees but the freezer had no problems. Turns out that the evaporator fan motor was dead.

  • Customer: Charles from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions in the video associated with the part that I ordered. The video was perfect and described everything I needed to do clearly. Repair is 100% successful!

Freezer cold and frig warm

  • Customer: William from Miami FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Replaced evap motor. Everything is strong and running like a champ. Partselect video examples were very helpful. Would order parts again on next problem. Thanks

fridge side was getting warm.

  • Customer: Darryl from Russellville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

refer quit cooling and so did freezer

  • Customer: jerry from petaluma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!

Freezer wouldn't go in to defrost cycle

  • Customer: John from Long Beach CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After some troubleshooting to ensure the thermostat and heating element were working, determined that the defrost timer was the problem. With the defective part, I was able to manually advance the timer to activate the defrost cycle, but it wouldn't do so on its own. Unplugged the refrigerator from the wall. Timer is located in the refrigerator compartment at the very top. The compartment houses the cooling thermostat, the light bulb and the defrost timer. Using 1/4" nut driver, remove 4 screws holding compartment cover to top of fridge. Lower a bit to access electrical wiring. Wiring harness can be unplugged to work on the timer away from the fridge which makes it a bit easier. Timer is mounted with 2 phillips head screws. Remove screws and unplug timer from wiring. Install new timer, plug in wiring, secure with the phillips head screws and remount entire compartment.

Broken door shelf retaining rail

  • Customer: Brian from Sterling VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It took less time to change out the rail than it did to take all the items off the shelf. Literally. Old rail holds on to the door with two snap in notches. I was able to easily unsnap the two ends of the broken rail and snap in the new rail in less than 30 seconds. No tools or mechanical knowledge needed.

Faulty defrost timer. Freezer would not maintain temperature

  • Customer: Steve from Nineveh IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched the video once. Removed four 1/4 inch screws with a nut driver unplugged the unit, took out two screws securing the timer. Replaced did all of this in about 10 minutes. It was "exactly" as the video showed and it's worked perfectly since the replacement of the faulty timer. I saved a $75.00 service call minimum and the part was more than likely cheaper from Part Select than from the repair facility. Although I'm a pretty good handy man, you would not need any experience to make this repair. The instructions are precise and the part fit perfectly.

broken retainer bar

  • Customer: christina from norman OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
super easy snaps Into place in a matter of seconds I wish I would have done it a long time ago

Frig did not run

  • Customer: hugh from delray beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simply replaced the defrost timer located inside the frig just behind the temp dial. Very easy job. Removed the 3 screws holding the temp sw and light assembly. Removed the defrost timer w/ 2 screws and put i all back together. 15 mins at most. Suggest you watch the install video for pointers.

Old gasket was torn causing excessive moisture in refrigerator.

  • Customer: Joseph from Cape Coral FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed door, removed old gasket, cleaned surfaces where gasket sealed, replaced gasket, re-installed door. About 10-15 min.

not cold enough

  • Customer: Gary from Hudson FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section

When I opened the door, sometimes the light was not turned on.

  • Customer: Helen from Burnsville MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
With the help of a knife we took out the light switch unplugged it, plugged in the new one and it started working.

Broke Pan Cover Glass Insert

  • Customer: Sheila M from Rosadale NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It slips right on. The hardest was getrthe item unpacked. It was pacrvery well for shipment so it wouldn't get broken. This company has very nice customer service on the phone.
All Instructions for the WRT21S4AW3
166-180 of 279