WRT1G3EW3 Westinghouse Refrigerator - Instructions

Removed old fan motor and installed new one.Not much room for big hands back there.Flexible extensions valuable on this job.

Instructions from partselect were very clear and probable cause made it easy to narrow things down. I have the manual for the refrigerator that shows the location of the defrost timer. Very surprised that it turned out to be a cheap and easy fix.

I just snapped-on the bar to the refrigerator door. It took less than 30 seconds and the repair was complete! I am so happy!

detached with screwdriver and applied the new one the same way. very easy

Ordered the part from this site . Part was delivered in 4 days.removed meat drawer, removed main shelf that the rails are attached to,unscrewed broken rail with Philips head screwdriver,reattached new rail and WALA finished.Less than fifteen minutes.

The glass inserted easily into the space formerly occupied by the original shelf

took off cardboard removed two screws holding fan housing. Removed new fan and housing from box and mounted new fan to new housing (two screws). Installed new fan and housing. reinstalled cardboard and plunged in power cord. Perfect fit.

The parts came two days after I ordered, they were the correct part and went in with ease. Couldn't be more happy with service from parts select. Awesome job.

Got the glass in two days time. Slid into the frame. It took less than 2 min. Great service from nice people. And the price of the glass was less than I expected. Thanks Dean

purchased a defrost theromast,took about 20-30 minutes to take apart & put back together.delivery was in one day from the time of my purchase.thanks for all ur help &prompt delivery.

Removed the timer, installed the new one. Great service from part select

the bottom door shelf bracket had broken in half, i unsnapped the two halves, i ordered the replacment part from part select which had sent the part within the time frame they promised and just snapped the bracket back in place. the whole process took less then two minutes.

Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!

Removed shelf unscrewed screw on both supports replaced and secured.

Refrigerator and freezer was not cooling sufficiently due to an inoperative evaporator cooling fan. Replacing the mini evaporator fan was extremely easy. Here are the steps needed to replace the fan. Step 1: Unplug refrigerator/freezer main power cord from the electric wall outlet. Step 2: Remove the food rack from the freezer compartment. Step 3: Using a 1/4" nut driver, remove the (2) 1/4" screws that hold the freezer vent panel/temperature control in place. Step 4: After removing the screws, disconnect the motor's wire harness connector which is located on the top left corner behind the freezer's vent panel/temperature control. Step 5: Pull away the entire vent panel/temperature control panel and lay it flat on a table. Step 6: Remove the vent cover from the main panel by holding the left side and the right side of the vent cover and squeeze both ends at the same time. Step 7: With the motor now being visible pull the motor's fan blade straight off. Step 8: Using the 1/4" nut driver, remove the (2) screws that hold the motor bracket to the rear of the main panel. Step 9: Using the 1/4" nut driver remove the (2) screws that hold the motor to the bracket and the (1) ground wire screw. Step 10: Install new motor back onto the bracket with the original (2) screws and the (1) ground wire screw onto the same locations.Step 11: Re install the (2) screws that mount the fan bracket to the back of the main vent panel.Step 12: Push the motor's original fan blade back on the shaft until it's fully seated. Step 12: Snap back in place the small vent panel back onto the main panel. Step 13: Push in place until you hear a click, the motor's wiring harness connector back onto the top left corner of the freezer's main power wire harness connector. Step 13: Push the main vent panel until it's in place and then reinstall with the original (2) 1/4" screws. Step 14: Reinstall the freezer's food rack back in place. Step 15: Plug in the main power cord into the wall outlet. Get ready to enjoy ice cold drinking water and a super cold freezer. Pete,your weekend mechanic