Models > WRT1G3EW0 > Instructions

WRT1G3EW0 Westinghouse Refrigerator - Instructions

All installation instructions for WRT1G3EW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRT1G3EW0
286-300 of 314
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Left side rail of meat draw broken

  • Customer: Derek from Brooklyn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the rack from the refrigerator. Then I used a Phillips screwdriver to remove screw from old part then screwed the on the new part to the rack.

Freezer cold and frig warm

  • Customer: William from Miami FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Replaced evap motor. Everything is strong and running like a champ. Partselect video examples were very helpful. Would order parts again on next problem. Thanks

Support rail for meat drawer broke (again).

  • Customer: Peter from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took out the shelf, removed the rest of the broken rail, replaced it. Piece of cake. (Note: The meat drawer support rails on this otherwise good refrigerator are very flimsy and break with some regularity even when the meat drawer isn't heavily filled. A good idea to keep spare support rails at home.)

fridge side was getting warm.

  • Customer: Darryl from Russellville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

Freezer wouldn't go in to defrost cycle

  • Customer: John from Long Beach CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After some troubleshooting to ensure the thermostat and heating element were working, determined that the defrost timer was the problem. With the defective part, I was able to manually advance the timer to activate the defrost cycle, but it wouldn't do so on its own. Unplugged the refrigerator from the wall. Timer is located in the refrigerator compartment at the very top. The compartment houses the cooling thermostat, the light bulb and the defrost timer. Using 1/4" nut driver, remove 4 screws holding compartment cover to top of fridge. Lower a bit to access electrical wiring. Wiring harness can be unplugged to work on the timer away from the fridge which makes it a bit easier. Timer is mounted with 2 phillips head screws. Remove screws and unplug timer from wiring. Install new timer, plug in wiring, secure with the phillips head screws and remount entire compartment.

Broken door shelf retaining rail

  • Customer: Brian from Sterling VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It took less time to change out the rail than it did to take all the items off the shelf. Literally. Old rail holds on to the door with two snap in notches. I was able to easily unsnap the two ends of the broken rail and snap in the new rail in less than 30 seconds. No tools or mechanical knowledge needed.

Faulty defrost timer. Freezer would not maintain temperature

  • Customer: Steve from Nineveh IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched the video once. Removed four 1/4 inch screws with a nut driver unplugged the unit, took out two screws securing the timer. Replaced did all of this in about 10 minutes. It was "exactly" as the video showed and it's worked perfectly since the replacement of the faulty timer. I saved a $75.00 service call minimum and the part was more than likely cheaper from Part Select than from the repair facility. Although I'm a pretty good handy man, you would not need any experience to make this repair. The instructions are precise and the part fit perfectly.

broken retainer bar

  • Customer: christina from norman OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
super easy snaps Into place in a matter of seconds I wish I would have done it a long time ago

Frig did not run

  • Customer: hugh from delray beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simply replaced the defrost timer located inside the frig just behind the temp dial. Very easy job. Removed the 3 screws holding the temp sw and light assembly. Removed the defrost timer w/ 2 screws and put i all back together. 15 mins at most. Suggest you watch the install video for pointers.

Old gasket was torn causing excessive moisture in refrigerator.

  • Customer: Joseph from Cape Coral FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed door, removed old gasket, cleaned surfaces where gasket sealed, replaced gasket, re-installed door. About 10-15 min.

drawer support rail broke just behind the front of the rail.

  • Customer: William from Buckeye AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unloaded the shelf and removed shelf. unscrewed the one screw and removed the rail. inserted new rail and replaced the screw. DONE.

Broke Pan Cover Glass Insert

  • Customer: Sheila M from Rosadale NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It slips right on. The hardest was getrthe item unpacked. It was pacrvery well for shipment so it wouldn't get broken. This company has very nice customer service on the phone.

both retainer bars broke within the first year..

  • Customer: George from Highland KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The new ones popped right in no problems

The freezer door shelf retainer bar was broken

  • Customer: Charles from Dimmitt TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
1.) Removed the old broken freezer door retainer bar. 2.) Removed the new freezer door retainer bar from shipping carton. 3.) Inserted new freezer retainer bar into place. 4.)Done is less than 4 minutes.

Shelf was broken

  • Customer: Gay from Carlsbad CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Clicked in beautifully....no problems at all.
All Instructions for the WRT1G3EW0
286-300 of 314