Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRT18CVAD2

WRT18CVAD2 Frigidaire Refrigerator - Overview

Get Parts and Repair Help for WRT18CVAD2

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRT18CVAD2, or you can search by name or part description. You can also find your part by where it is located on the WRT18CVAD2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRT18CVAD2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the WRT18CVAD2

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$5.65

Crisper Drawer Cover Support

$15.70

Defrost Thermostat

This limiter thermostat cuts out when the temperature inside your refrigerator reaches 55 degrees Fahrenheit and kicks back in when the internal temperature drops to 20 degrees Fahrenheit. If you discover temperature issues with your refrigerator or freezer, the defrost thermostat may need to be replaced. You will need tools for this repair, including a 1/4-inch nut driver, a pair of wire strippers, and a heat gun. Be sure to disconnect power to the refrigerator before completing this repair. The defrost thermostat is located behind the back panel of your side-by-side refrigerator/freezer. You will first need to remove the panel and take the defrost thermostat out to complete the repair.

$6.34

Hexagonal Screw

Sold individually.

$27.48

Evaporator Fan Blade

This evaporator fan blade is a genuine OEM part that is sourced directly from the manufacturer. The evaporator fan blade circulates air through the refrigerator to control the amount of cold air goes that goes to internal compartments of the unit. It may need to be replaced if the fridge is noisy or not cold enough. This part is made of plastic and is sold individually. It will be necessary to disconnect power to the refrigerator and empty the freezer compartment of the refrigerator. The tools needed to complete this repair are a 1/4 inch nut driver and a pair of needle nose pliers.

$6.55

SCREW

Sold individually.

$8.86

Door/Light Switch

This is a door/light switch and it is a replacement part for your refrigerator. This part is activated as you open and close your refrigerator door. When the switch is activated and the door is open it will turn the light on inside your appliance, and when you close the door the switch will deactivate the light. Before purchasing this part, you may test it for continuity to determine if your current switch is defective and needs replacing. This model is white in color and measures to be roughly one inch thick, almost two inches high, and almost 1.5 inches deep, with a male end plug.

$2.58

Ice Cube Tray

The ice cube tray is made of plastic, is white in color, and is sold individually. This is a part for your freezer. The ice cube tray is sturdy but flexible to allow you to easily ...

$8.38

Door Hinge Pin Bearing

This white hinge pin bearing pivots the freezer and refrigerator door.

$2.04

TAPPING PLATE

$88.98

Door Gasket

This almond door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air out.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door seals cracking from age on both compartments

  • Customer: Clark from Wenatchee, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 19 of 23 people found this instruction helpful
Located the many screws which hold the inside surface of the door on. The screws are located between the seal and the inside surface; you have to hold back the seal to find the screws.

The seals are attached to this inner surface by a snug fit, and clamped in place when the screws are tightened again. Its simpler than it sounds.

Final... read more

freezer kept icing over, refrigerator too hot

  • Customer: debra from new washington, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 10 of 12 people found this instruction helpful
First, I unplugged the appliance. Safety, first.
Than I removed the shield which was held in by screws. This covered the fan, thermometer.
The defrost thermostat was taken out, with a little extra force. The wires on the defective part were no longer attached to the part. The instructions were easy to follow in replacing the defrost thermostat. I... read more

my shelf supports broke

  • Customer: michael from hanford, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
I pulled out the old pieces and poped what I couldn't into the foam insulation behind the support. Then I placed the new piece in the hole and popped the plastic pin to seat the support. bang. the only problem I had was knowing if it was the right part by the picture. The little pin that had to be pushed through kinda threw me. read more