Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS6R3EW8 > Instructions

WRS6R3EW8 Westinghouse Refrigerator - Instructions

All installation instructions for WRS6R3EW8 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS6R3EW8
91-105 of 736
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken shelf

  • Customer: Johan from Schenectady, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 10 people found this instruction helpful
Snapped the shelf into place

lighting hit the house

  • Customer: keith from villa rica, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 23 of 49 people found this instruction helpful
first i by passed the timing board, with a ele cord to the fan motor to keep the fridge cool till your parts got here, which was realy fast delivered,
the fan would come on because the board was fried.
it took abot 30 min to install every thind just be carefully unpluging anything.things will break i guess metal eing cold makes the conne4ctors stick together.
evaporator fan is in the frezzer four screws,tested the wires for ohms,and power, when i pluged in the fan i would loss power to the fan,that told me the board was bad, the same night my furnance when to (reaaly) and i lost my borad on the computer ethernet card (lighting isn't fun) it cost to fix everything about 130.00 thanks for thr great parts

I broke the bottom door shelf by "forcing" in too many jars

  • Customer: Marc from Oberlin, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 13 people found this instruction helpful
The new bin arrived, I slid it in place and away we went.

Refrigerator was not cooling

  • Customer: Vicki from Johnson City, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 19 people found this instruction helpful
This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

replace old water filter

  • Customer: Dung David from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 11 people found this instruction helpful
The untwisted the water filter took out the old water filter and replaced it with the new one and twisted the cover back on. it was very easy to do and now the water tastes very fresh :) thank you

starter smoking when first coming on

  • Customer: Michael from Ayden, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 20 people found this instruction helpful
The retaining wire keeping the starter in place was first removed then the starter was easily removed. Pulling the old wire off was a little difficult because I had to pull harder than I expected. Getting the wire back on was probably the hardest part. I had to compress one part of the plug so I could get it to fit back on then it was simply a matter of placing the starter back in position and replacing the wire that holds it snugly in place. 20 minutes or so start to finish and new starter works well.

water valve failure

  • Customer: Robert from Louisville, KY
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 12 of 17 people found this instruction helpful
removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

Refrigerator quit running

  • Customer: Frederic from Daytona Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 20 people found this instruction helpful
I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

Ice Actuator broken, Door Closing Cam, Door Closure/Hinge Bearing

  • Customer: Ken from Diamond springs, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 13 of 21 people found this instruction helpful
Unplug refrigerator. Take out spill tray by sliding out. remove bottom 3 screws, gently but firmly push up and against refrigerator(Top section of cover snaps in by pulling cover down while holding cover against refrigerator). There is a ribbon wire connecting the two boards, care not to tear it out of connectors. There are two tabs on the plastic connector holding the ribbon wire to the outside board,pull the tabs out a little and gently pull the ribbon loose, carefully. There are 3 screws holding in the back board, remove them, them remove water hose from water actuator so the assembly can come out. Gently spread the plastic holder to be able to take the broken paddle out. Watch closely how the third arm on the actuator(Lower left arm)is resting on the back of the flapper.Replace the Actuator exactly the same. Just reverse the steps to install the rest of the parts.(Had a time getting the water hose back into it place. I used pliers to push and wiggle it back into it opening).Don't forget to plug the frig back in again. DOOR CLOSING CAM AND HINGE BEARING ARE VERY EASY. It take about 10 to 15 minutes to do. Empty door drawers before procedure the screw holding the plastic cover, remove cover. I used a 3/8" nut driver and my cordless drill to take out the two lag bolts holding the top hinge.Lift door off bottom hinge. Replace Door Closure/Hinge Bearing. Reverse procedure to finish installation.

Food compartment not cooling, freezer working well.

  • Customer: Mary from Kenmore, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 18 people found this instruction helpful
Fantastic!
Sent in a brief description of problem and model number. Reply and description of other customers experiences guided us to the exact problem.
We ordered the part on Friday and it was here on Tuesday.
I prepared the freezer compartment for the removal of the old motor and on Sunday husband installed new Evaporator Fan Motor.

It works and is cooling like it did when it was new.

This has been a great experience as all repairmen wanted at least 60.00 to just come out and determine what the problem was. I can only imagine what the final bill would have been.

This was easy and inexpensive.

Thanks for all the help.

Water was leaking from under and in the fridge

  • Customer: Enrique from Harpswell, ME
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench set
  • 10 of 12 people found this instruction helpful
First I took both bolts off of the housing (holds filter) and removed two hoses by holding elbow vavle in while pulling hoses. Did the reverse to replace. The trick was knowing how to remove the elbow valves. Second there was still water leaking under the fridge, discovered it was the water inlet valve underneath. Ordered that part.

broken door shelf bin

  • Customer: Elsie from Effingham, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
Opened the package- popped the shelf in- good as new!!!

Broken Door Bin

  • Customer: Peter from Whittier, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
Item shipped Insanely Fast, ONE DAY.
Item was installed in 15 seconds, faster than it took me to remove it from the box!

water actuator broke

  • Customer: Robert from Port Neches, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
First I removed the plastic drip pan that catches the ice and water. There were two or three screws that had to be removed. Next I removed the old broken actuator and put the new one in. There were two more screws to be removed to replace the old actuator. Those screws were pretty small and hard to get out. Other than that, the new actuator went right in and was working in no time. Overall a pretty easy project.

Original gate broke at the swivel point

  • Customer: Charles from New Orleans, LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 10 of 14 people found this instruction helpful
I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!

This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
All Instructions for the WRS6R3EW8
91-105 of 736