Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS6R3EW8 > Instructions

WRS6R3EW8 Westinghouse Refrigerator - Instructions

All installation instructions for WRS6R3EW8 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS6R3EW8
691-705 of 736
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the drive blade for ice maker was rusted

  • Customer: Michael from Philadelphia, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .

The ice maker quit producing ie

  • Customer: Tommie from Port Lavaca, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Purchased a new ice maker assembly and installed. Very easy

Broken shelves

  • Customer: Pamela from Brooklyn, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy to install (self explanitory)

Botton door bin was broken.

  • Customer: DEBRA from EDMOND, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simple replacement. Fit perfectly.

frost build up in side on the back of the freezer .and my my filter housing cup crack due to ice build up inside .freezer side not to cold and fridge side to cold freezer and fridge side to factory settings

  • Customer: Carlos from Newton, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you

refrigerator ice maker was not making ice, water on floor

  • Customer: Richard from Rogersville, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
used videos and followed instructions to repair. The water inlet valve was first changed because no ice was being made. Changed ice maker due to no cycle and no sound came from it. The water filter was then changed due to length of time since last changed. Plugged up refrigerator and turned water back on and within 2 hours we had ice again.

the ice auger, and ice crusher broke

  • Customer: Charles from Splendora, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just slide out the old part, slide in the new one, took less than 10 min

When the ice maker was filling the ice tray with water, the water would come out the water dispenser at the same time.

  • Customer: Greg from Murrieta, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

Wiring harness too thick to fit where the instructions told me to put it.

  • Customer: SHARON from Lynchburg, VA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After trying several times to fit the wiring harness beside the ice maker without any success, I folded the wiring harness behind the ice maker. Between it and the back of the freezer.

Missing door shelves and bins required replacement for my refrigerator

  • Customer: Pamela from LAWRENCEVILLE, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The replacement pieces for my refrigerator were easy to install and took about 3 mins to attach 3 shelves and 1 bin.

ice crusher cylinder.

  • Customer: JoAnn from Davie, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ice crusher cylinder broke (its plastic). I use a lot of crushed ice. I just ordered the entire drawer. It was just easier to just remove the old one and push this in. If one part goes then another will follow soon Works great.

replace a shel on the door of the refrigerator

  • Customer: Gerald from Brooklyn, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just hung it on the door. thanks for your speedy delivery. i was great to do business with your company. i will be ordering down the road. thanks again.

broken crisper drawer support

  • Customer: Genevieve from Herndon, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

Hinge on bin broke

  • Customer: Barbara from Mount Juliet, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply placed new bin in place. Took less than 60 seconds.

Through the door water slow

  • Customer: PHILLIP from BAKERSFIELD, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Turn off the ice maker.You don't need to turn off the water. Find the water filter in the upper right corner of the refrigerator. It's the round thing with a shallow round depression in the center. Push in on the center and release. The old filter partially pops out. Remove it.and throw it away. Insert new filter and push until it locks in place. Run water through the new filter until it runs clear.
All Instructions for the WRS6R3EW8
691-705 of 736