Models > WRS6R3EW8 > Instructions

WRS6R3EW8 Westinghouse Refrigerator - Instructions

All installation instructions for WRS6R3EW8 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS6R3EW8
676-690 of 691
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water Dispenser broke

  • Customer: Theresa from Clinton Twp MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instructions on video from Instance Repairman. Very easy to follow directions. He does step by step instructions.

Broken ice maker bin and auger

  • Customer: Jane from Washington GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out the old one and pushed in the new one. Easy, peasy.

no problem

  • Customer: Frank from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pull the old one out and stick the new one in. Its just that simple.

Ice was not dispensing.

  • Customer: Sheree from New LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced ice container and auger assembly. (pulled the old one out and slipped the new one in) PROBLEM SOLVED! IT WAS SO EASY AND SO COST FRIENDLY! I LOVE TO FIX THINGS MYSELF AND THIS WAS REALLY EASY!

refer quit cooling and so did freezer

  • Customer: jerry from petaluma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!

The ice maker quit making ice.

  • Customer: Kenneth from Allen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

Crisper support 'pin' for crisper broke off x 2

  • Customer: KENNETH from GLASTONBURY CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
1) cleared remaining parts of broken crisper supports by pushing them into refrigerator insulation(pushed on 'pegs' so 'peg' holes in side of plastic inner liner of refrigerator were clear. 2) Was unable to fully place new crisper supports into postiion. 3) Then, out of despiration, used small light hammer to gently tap on largest 'pin.' I was surprised to see this 'pin' enter into plastic side of refrigerator and then to see crisper support was secure when 'pin'/peg' was flush with new crisper support. 4) then returned crisper to correct postion; supports held. 5) WARNING-DO NOT OVERLOAD CRISPERS!! I BELIEVE THIS CAUSED 'PIN'/'PEG' FAILURE INITIALLY! I don't know if cause was volume too high with crisper forced into place OR if the crisper mass/weight was the culprit. SUGGEST weight limit less than 7.5 lbs.; don't attempt to load in more volume than top of crisper.

Our refrigerator ice maker was broken, crisper draw was broken, and shelf support was broken.

  • Customer: Gary from North Smithfield RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We decided to get a new fridge, after the " sticker shock " of new refrigerators we decided to repair the one we have. Two screws and one plug and the ice maker was replaced, took out the broken crisper shelf, put in the new one and that was done, instructions were great. I actually had to watch a " how to " video, ( provided by your web site ) to change the shelf support, very easy. thanks, Gary Hoyle

The Fresh Drawer for veggies cracked, so I ordered a new one.

  • Customer: Julie from Westhampton NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All I had to do was take the old drawer out, and put the new drawer in. You would think this would be very easy. But there was a hitch. There is a little lever on the drawer that you can slide to the right or to the left in order to adjust the temperature of the drawer. That piece was not included. It had to be purchased separately. No one told me that. So I tried to take the slider out of the old box. I could not get it out without breaking it, so I called the company. They said that piece is not included, and it had to be purchased separately. However, one could take it out of the old drawer and put it into the new drawer. When I told them that I could not figure out how to do this without breaking it, someone in customer service said to use a screwdriver and gently try to pry the old one off, and then inserted into the new one. I cannot believe that this integral piece was not part of the plastic drawer!

Popping noise each time refridgerator door was opened.

  • Customer: Joseph from Bella Vista AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed top hinge, lifted door off, replaced lower hinge bracket and cams. Replaced door. Part fit perfectly in spite of a design change. No more annoying popping noise.

"Popping" noise when opening the refrigerator door.

  • Customer: Alan from Plantation FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the food on the door and placed it in the refrigerator. I placed a plastic sheet over the opening of the refrigerator to keep the cold air in. Then I removed the bracket for the upper hinge, remover the door and placed it onto a table. Then I removed the plastic bearing from the bottom of door. I then replaced it with the new bearing. Then I removed the lower bearing and its bracket from the refrigerator. At this point I had to modify the new lower bracket by removing the alignment tab with a dremel because there wasn’t any hole in the housing for it. Then I attached the new bracket and bearing. Replaced the door and upper hinge and the job was complete. It took only about a half an hour to finish.

Our refrigerator was not cooling below 50 degrees but the freezer had no problems. Turns out that the evaporator fan motor was dead.

  • Customer: Charles from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions in the video associated with the part that I ordered. The video was perfect and described everything I needed to do clearly. Repair is 100% successful!

Leaking from refrigerator

  • Customer: WALTER R. from SHEFFIELD VILLAGE OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Had a leak every night from refrigerator couldn't understand where from. Went on line and found some articles. I was referred to this sight by ads the articles and then in how to. I was pleased that a customer wrote their own instructions on what to do it was more concise clear and made preparation easier. First label towel cup and bucket needed too. Turn off water supply and electrical cord unplug then remove cover behind refrigerator vacuum and clean then. Water makes a mess so clean dry first. Then mark your hoses to remember order. Next remove old inlet and put in bucket it's pressure clamps so push in and it locks I chose to suction pipes and check for damage to pipes pin holes etc next I inserted into new inlet in order. At that time I turned water valve on checked for leaks at initial insert and new inlet. Next I plugged in unit cord. Waited. No leaks so far left for 30 minutes ran ice machine and water dispenser waited 20 minutes no leaks yet. Unplugged refrigerator unit. Installed the inlet completely to base and closed back paper panel after wiping water. Waited 24 hours then smiled no leak. Job done so far 2 weeks all clear. Hope this helps you will need screws driver and wrench for copper or main line I did find same part for less but this sight help me with good instructions the one they provide is for engineers architects lol not me I'm DYI

Ice Maker Not Getting Water

  • Customer: Edward from Cuba NM
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

no water flowed to the ice maker

  • Customer: Levern from Mc Donald TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.
All Instructions for the WRS6R3EW8
676-690 of 691