Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS6R3EW6 > Instructions

WRS6R3EW6 Westinghouse Refrigerator - Instructions

All installation instructions for WRS6R3EW6 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS6R3EW6
706-720 of 809
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

frost build up in side on the back of the freezer .and my my filter housing cup crack due to ice build up inside .freezer side not to cold and fridge side to cold freezer and fridge side to factory settings

  • Customer: Carlos from Newton, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you

refrigerator ice maker was not making ice, water on floor

  • Customer: Richard from Rogersville, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
used videos and followed instructions to repair. The water inlet valve was first changed because no ice was being made. Changed ice maker due to no cycle and no sound came from it. The water filter was then changed due to length of time since last changed. Plugged up refrigerator and turned water back on and within 2 hours we had ice again.

the ice auger, and ice crusher broke

  • Customer: Charles from Splendora, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just slide out the old part, slide in the new one, took less than 10 min

When the ice maker was filling the ice tray with water, the water would come out the water dispenser at the same time.

  • Customer: Greg from Murrieta, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

Not making Ice/ unit not calling for water

  • Customer: Bob from Celina, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug refrigerator power cord. Remove ice cube bin. Place wire signal arm in down (off) position. Ice Maker is held in place by two (slotted/hex headed) screws through keyhole slots over the top of Ice maker along the left side of freezer. Use mirror to locate screws then carefully loosen (do not remove) screws with a nut driver or screw driver. Lift Ice maker up and right until it releases from the screw heads. Unplug electrical connection. A flat screw driver may be required to loosen connector. Connect new unit electrical and Install new unit over screw heads and tighten screws. Replace Ice Bin and place wire signal arm in the up (on) position. Reconnect refrigerator power cord. After freezer cools down sufficiently it will start making ice.

Wiring harness too thick to fit where the instructions told me to put it.

  • Customer: SHARON from Lynchburg, VA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After trying several times to fit the wiring harness beside the ice maker without any success, I folded the wiring harness behind the ice maker. Between it and the back of the freezer.

Missing door shelves and bins required replacement for my refrigerator

  • Customer: Pamela from LAWRENCEVILLE, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The replacement pieces for my refrigerator were easy to install and took about 3 mins to attach 3 shelves and 1 bin.

ice crusher cylinder.

  • Customer: JoAnn from Davie, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ice crusher cylinder broke (its plastic). I use a lot of crushed ice. I just ordered the entire drawer. It was just easier to just remove the old one and push this in. If one part goes then another will follow soon Works great.

replace a shel on the door of the refrigerator

  • Customer: Gerald from Brooklyn, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just hung it on the door. thanks for your speedy delivery. i was great to do business with your company. i will be ordering down the road. thanks again.

broken crisper drawer support

  • Customer: Genevieve from Herndon, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

Hinge on bin broke

  • Customer: Barbara from Mount Juliet, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply placed new bin in place. Took less than 60 seconds.

Through the door water slow

  • Customer: PHILLIP from BAKERSFIELD, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Turn off the ice maker.You don't need to turn off the water. Find the water filter in the upper right corner of the refrigerator. It's the round thing with a shallow round depression in the center. Push in on the center and release. The old filter partially pops out. Remove it.and throw it away. Insert new filter and push until it locks in place. Run water through the new filter until it runs clear.

Auger Not Driving Ice Out The Front

  • Customer: JeRay from Arizona City, AZ, AZ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Taking it apart is sort of common sense, however putting it back together can be made a lot easier using todays technology of . Digital photography. Take pictures at each stage of disassembly and reassembly be comes very easy and you may only have to do it once instead of multiple times.

Frige and freezer not cooling

  • Customer: FRANK from BRADENTON, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

Auger in ice maker was wore out. Blade was sliding backward.

  • Customer: Dorthy from Aurora, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old ice container. Washed and dried the new one and installed. Works wonderful.
All Instructions for the WRS6R3EW6
706-720 of 809