Models > WRS6R3EW4 > Instructions

WRS6R3EW4 Westinghouse Refrigerator - Instructions

All installation instructions for WRS6R3EW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS6R3EW4
691-705 of 707
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker Not Getting Water

  • Customer: Edward from Cuba NM
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

The refrigerator's In-door water dispenser leaked water. The leakage started out slow and over a period of time increased.

  • Customer: Frank from Mentor OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench set
  • 0 of 0 people found this instruction helpful
This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

no water flowed to the ice maker

  • Customer: Levern from Mc Donald TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

Refrigerator light out

  • Customer: Lynne from Collegeville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Once I had the right part, it was very easy. The bulb had melted to the part and blew the bulb. To change the filter was a breeze. Thank you for all your help in getting the right part.

Installed a extra shelf

  • Customer: nathan from Buckley WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pushed the shelf pegs in the wholes

Water Dispenser broke

  • Customer: Theresa from Clinton Twp MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instructions on video from Instance Repairman. Very easy to follow directions. He does step by step instructions.

Replace water dispenser Actuator

  • Customer: Phillip M. from Melbourne FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the water tray. Remove 3 screws at bottom of cover with Phillips screwdriver. Slid frame upward, disconnect wires from door. Remove screws that held the water actuator. Took broken water actuator out, slid new one in. Screw in place. put parts back in place and bingo, all done. Easy!!!

The ice maker had shorterd and was no longer making ice cubes

  • Customer: William from Chaparral AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I used a nut driver to loosen two mounting screws, disconnected the wiring harness, and removed the ice maker. I transfered the level bracket from the old ice maker to the new ice maker and re-installed the new unit - connected the wiring harness and tightened two mounting screws. Once installed, I had to make minor adjustments on the front of the unit to get the ice maker to produce "full sized" cubes. Instalation took about ten minutes. Adjusting took 2 or 3 cycles of the ice maker to achieve properly sized cubes.

ice maker quit working, then leaked water

  • Customer: Rodney from Federal Way WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
watched a youtube video in removing and replacing the unit which made it very easy to follow through. we actually went without the ice maker for 6 months before this not realizing how easy and affordable it was to replace.

Ice maker was making a ticking sound as the drive motor for the ice cube tray was slipping.

  • Customer: Karl from Sparta MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair was very simple with loosing the two mounting screws (did not have to take completely out) with a nut driver. Unplugged the unit from the fridge wiring at the back of the pig tail on the ice maker. The pictures on the web page were priceless in making the decision if I truly had the correct part. The part arrived within two day from ordering. Ordered on Sunday and received on Tuesday. Took about 10 min to unpack, mount, hook up electrical and turn on water.

ice maker just quit harvesting cycle

  • Customer: Rudolph from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
ice maker i received went in place of the old one with no problems or having to modify anything.Just loosened the two mounting screws and lifted out old one and new went in its place.very easy!

Ice maker leaking water into the storage bin

  • Customer: Herbert from Claremont NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Shut the water off to the refrigerator. Loosened the two mounting bolts on the icemaker and lifted the old ice maker straight up. Unplugged the wire harness. The old ice maker had a 90 degree metal bracket mounted underneath the ice maker that rested on the wall of the freezer. I marked the bracket around the screw with a sharpie and removed the bracket and put it on the new ice maker in the same position that I marked. This bracket will keep the new ice maker level in the freezer. Plug in the harness on the new one. Slide it over the mounting bolts making sure the water through is in the icemaker and tightened the mounting bolts. Ice maker may take a while to cycle through, up to 24 hours, to start making ice. Done.

no problem

  • Customer: Frank from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pull the old one out and stick the new one in. Its just that simple.

Ice was not dispensing.

  • Customer: Sheree from New LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced ice container and auger assembly. (pulled the old one out and slipped the new one in) PROBLEM SOLVED! IT WAS SO EASY AND SO COST FRIENDLY! I LOVE TO FIX THINGS MYSELF AND THIS WAS REALLY EASY!

Ice auger no longer functions

  • Customer: Tony from Hendersonville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply turned off ice maker, carefully pulled the old assembly straight out, slid the new assembly in place, making sure the motor connection was correct...DONE!
All Instructions for the WRS6R3EW4
691-705 of 707