Models > WRS6R3EW2 > Instructions

WRS6R3EW2 Westinghouse Refrigerator - Instructions

All installation instructions for WRS6R3EW2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS6R3EW2
706-720 of 808
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker quit making ice, clicking noise coming from lower rear of appliance

  • Customer: Paul from Cincinnati, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
If this happens to you the first thing I would do is shut off the freezer and, using a hair dryer, melt the ice in the ice maker and heat up the water inlet to make sure it is not froze up. Turn the freezer back on and wait to see if that cures the problem. If not, order the new water inlet valve and follow the simple instructions in the video provided on the PartSelect website. I have never have a more pleasant experience with any parts/repair service than I did with PartSelect. After ordering that part it came within the time they stated and their help with the install was great. Also helpful were the other customers talking about their problems and solutions.Thanks to PartSelect I now have Ice and a happy wife. Happy wife--happy life.

Quite making ice

  • Customer: Charles C. from Denver, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

ice maker was not making ice, no water flow into.

  • Customer: Mary from Mt Pleasant, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

Water Inlet Valve Not Working / No Ice

  • Customer: ROBERT from CLINT, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 0 of 0 people found this instruction helpful
Started at installing water inlet valve, but the valve I recieved did not have threaded ends for water lines. Was the replacement part I needed, but with out the threaded ends. Called partselect about the issue, they did there research about the valve, was told that the manufacture had changed some of the install features, so I aked them that instructions etc. , Would of been great. As I looked at the valve where the water lines go, they all matched in water line sizes that matched my original valve, so I cutted the water lines one by one making sure they go where they go. The new water valve requires to cut (flush cut) the lines at it's closest point to the valve and insert into valve water line hole (the new water inlet valve, has a seal gasket in each hole with locking teeth). So you must be accurate on where and which water line gos where, cause you won't be able to pull the water line out again with out damaging the locking teeth etc. , In that one water line you just putted in wrong. Basically the new water inlet valve is a cut water line flush and insert to proper hole, you got to push hard until you feel the water line pushing your hand away from you, which to me indicated that you had a solid complete sitting of water line on to valve and pull on that same line just a bit to see , if it would come out. Which it did not and so you do all water lines the same way / reinstalled / hooked up main water copper line the the water inlet valve / checked for leaks, nothing / installed ice maker simple 2 screws on inside of freezer for mounting ice maker / unplugged ice maker from male-female plug in freezer where ice maker is plugged to. Installed reverse order / added 1 cup of water (by hand) onto ice maker I had just installed, so it would go thru its cycle , of making ice / ice dispencing onto tub / and the water inlet valve kicks into action adding water. * Note: I did not have the instructions about the new changes to the water inlet valve , do this ,do that . The number provided to me from customer service on about contacting the manfacturer was useless, reason being. They just said that they just manufacture parts, they don't how to. But like I said, it's a simple cut even and push into hole, until line locks. Better instructions, with details. Would've been great . Hope my details help you all. : )

Leaking from refrigerator

  • Customer: WALTER R. from SHEFFIELD VILLAGE, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Had a leak every night from refrigerator couldn't understand where from. Went on line and found some articles. I was referred to this sight by ads the articles and then in how to. I was pleased that a customer wrote their own instructions on what to do it was more concise clear and made preparation easier. First label towel cup and bucket needed too. Turn off water supply and electrical cord unplug then remove cover behind refrigerator vacuum and clean then. Water makes a mess so clean dry first. Then mark your hoses to remember order. Next remove old inlet and put in bucket it's pressure clamps so push in and it locks I chose to suction pipes and check for damage to pipes pin holes etc next I inserted into new inlet in order. At that time I turned water valve on checked for leaks at initial insert and new inlet. Next I plugged in unit cord. Waited. No leaks so far left for 30 minutes ran ice machine and water dispenser waited 20 minutes no leaks yet. Unplugged refrigerator unit. Installed the inlet completely to base and closed back paper panel after wiping water. Waited 24 hours then smiled no leak. Job done so far 2 weeks all clear. Hope this helps you will need screws driver and wrench for copper or main line I did find same part for less but this sight help me with good instructions the one they provide is for engineers architects lol not me I'm DYI

The ice maker quit producing ie

  • Customer: Tommie from Port Lavaca, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Purchased a new ice maker assembly and installed. Very easy

Ice maker quit working.

  • Customer: Paul from Akron, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul

Water Dispenser Actuator Broken

  • Customer: marvin from columbia, TN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed tray by pulling out. Took out three screws at bottom. Lifted up on face plate. Remove three screws at top,pulled out to access actuator,relieved spring. Then took out screw on the right,loosened two screws on the left and removed broken part. Put in new part and reassembled.

I broke the bottom bin on the refrigerator door

  • Customer: Jane from Mequon, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The 2 door bins came in 3 days! I could not believe how fast the service was. The door bins just slid right into place, not tools required. They look great. Special shout-out to Jennifer T. who helped me over the phone. I placed the order for the bottom door bin and later realized that I could add one more door bin to the refrigerator door to make more storage area. I called the customer service number and she canceled my order. She sent me a follow up email and I was able to place a new order to get both door bins and save on shipping fee. PartSelect was great! Thank you!

broken shelves

  • Customer: Chase from Conyers, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
parts fit perfectly

Drawer support broke.

  • Customer: nancy from Bellingham, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I was worried that the support was a permanent fixture in the refrigerator wall. But I pried it out and replaced it with the new part. Holes were exactly the same size so the new part easily replaced the old one.

support clips broken for 2 bins

  • Customer: Thurlowe from Tampa, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Purchase was easy. Delivery was quick. Install videos was accurate. Made it eady to as DI project. Safe place for purchase and support. Saved on cost of professional visit.

Needed to replace split door seal

  • Customer: Maridell from Lexington, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It took about 5 minutes to pull the old seal out and replace with the new one. Simple enough for a 71 year old woman to do alone.

Refrigerator door would not close properly

  • Customer: Jeff from Rapid City, SD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We watched your video online and just followed the instructions. It was super easy to follow and install the new parts. We would highly recommend your site to anyone. The parts came in the mail in 3 days. Thank you very much for saving us to call a repair person and saving us about $100.

Compressor running constantly with freezer temperature at -20 degrees fahrenheit.

  • Customer: Steven from Raymond, NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Since the evaporator was all iced up, I decided to replace the least costliest item (defrost thermostat kit); did not resolve the problem. Once I replaced the freezer temperature control thermostat, the freezer temperature stabilized right at 0 degrees fahrenheit with dial on factory setting. Compressor no longer running constantly.
All Instructions for the WRS6R3EW2
706-720 of 808