Models > WRS6R3EW0 > Instructions

WRS6R3EW0 Westinghouse Refrigerator - Instructions

All installation instructions for WRS6R3EW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS6R3EW0
676-690 of 708
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water dispenser/ice maker inop

  • Customer: Michael from White Springs FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed old water pump and cut off ends of all lines. Plugged them into each water inlet/outlet and turned it on. Instant water to dispenser but took about 6 hours for ice maker to get water. Had to prime the ice maker. Works great and saved a lot of money ordering parts from you. Thanks.

meat shelf was broke

  • Customer: michael from kennewick WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
got the new one replased it and it was easy plus im certified in majjor apliences

support broke

  • Customer: Lisa from Mena AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just put it in the old hole. the hard part was getting the old one out. you have to poke the center piece in to remove. otherwise you will break your fridge. then you have to to pull the center piece out before you put new in.

refrigerator staying to warm

  • Customer: nicole from chipley FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
husband did it took only a few min part was easy to find

water valve leak

  • Customer: Donald from Wilmington NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.

broken suport for pam

  • Customer: JORGE from HOUSTON TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
take of the tray & take parts out & installed the new ones

Refrigerator door "clicked" when opening.

  • Customer: Clinton from Conyers GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Removed the nuts on top - to loosen the door. Lifted the door off the hinge. Took out old part, put in new one, reinserted door, replaced nuts.

One side of door shelf bin broke.

  • Customer: Janeen from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I originally ordered the wrong part (for the freezer side). Received the part on Saturday--I had ordered on Thursday afternoon. Discovered my error and got on line to see how to return and ordered the correct part. This part came on Tuesday morning. I put the part on the door and was finished in no time! Great service and easy return for my wrong order. Thanks.

refer quit cooling and so did freezer

  • Customer: jerry from petaluma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!

The ice maker quit making ice.

  • Customer: Kenneth from Allen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

Our refrigerator ice maker was broken, crisper draw was broken, and shelf support was broken.

  • Customer: Gary from North Smithfield RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We decided to get a new fridge, after the " sticker shock " of new refrigerators we decided to repair the one we have. Two screws and one plug and the ice maker was replaced, took out the broken crisper shelf, put in the new one and that was done, instructions were great. I actually had to watch a " how to " video, ( provided by your web site ) to change the shelf support, very easy. thanks, Gary Hoyle

Crisper support 'pin' for crisper broke off x 2

  • Customer: KENNETH from GLASTONBURY CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
1) cleared remaining parts of broken crisper supports by pushing them into refrigerator insulation(pushed on 'pegs' so 'peg' holes in side of plastic inner liner of refrigerator were clear. 2) Was unable to fully place new crisper supports into postiion. 3) Then, out of despiration, used small light hammer to gently tap on largest 'pin.' I was surprised to see this 'pin' enter into plastic side of refrigerator and then to see crisper support was secure when 'pin'/peg' was flush with new crisper support. 4) then returned crisper to correct postion; supports held. 5) WARNING-DO NOT OVERLOAD CRISPERS!! I BELIEVE THIS CAUSED 'PIN'/'PEG' FAILURE INITIALLY! I don't know if cause was volume too high with crisper forced into place OR if the crisper mass/weight was the culprit. SUGGEST weight limit less than 7.5 lbs.; don't attempt to load in more volume than top of crisper.

Broken Crisper Drawer Cover and broken Crisper Cover Support pin

  • Customer: Caesar from Calabasas CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Following the video instructions provided by the web site, it took me less than 20 minutes to accomplish the entire repair. The video instructions were invaluable, because without them I would not be able to guess how the support part is mounted in the refrigerator’s wall.

Orginal pin failed. I got tired of doing a balancing act with food on the shelf to take weight off the missing pin.

  • Customer: David from Council Bluffs IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just like the video. I had pulled all the parts of the old pin out of the frig months ago. I had tired to buy a replacement pin, but the local supply store could not get the correct part. I finally did a search and found your website. I was impressed with the pictures and the "how to" video.

The Fresh Drawer for veggies cracked, so I ordered a new one.

  • Customer: Julie from Westhampton NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All I had to do was take the old drawer out, and put the new drawer in. You would think this would be very easy. But there was a hitch. There is a little lever on the drawer that you can slide to the right or to the left in order to adjust the temperature of the drawer. That piece was not included. It had to be purchased separately. No one told me that. So I tried to take the slider out of the old box. I could not get it out without breaking it, so I called the company. They said that piece is not included, and it had to be purchased separately. However, one could take it out of the old drawer and put it into the new drawer. When I told them that I could not figure out how to do this without breaking it, someone in customer service said to use a screwdriver and gently try to pry the old one off, and then inserted into the new one. I cannot believe that this integral piece was not part of the plastic drawer!
All Instructions for the WRS6R3EW0
676-690 of 708