Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS3R3EWA > Parts

WRS3R3EWA Crosley Refrigerator - Parts

All parts for the Crosley Refrigerator WRS3R3EWA

Below is a list of all parts for the Crosley Refrigerator WRS3R3EWA. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the WRS3R3EWA
1-14 of 269
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.15

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support ...

$60.81

Water Inlet Valve

The water inlet valve is also known as the water inlet valve assembly and is compatible with your refrigerator. The function of this part is to release water from the supply line when activated, and send it through to your water dispenser in your refrigerator. To make this repair you will need an adjustable wrench, a quarter inch nut driver, and a sharp utility knife. Before you begin this repair make sure to disconnect the power supply to your refrigerator, as well as disconnect the inlet water supply from the back of the refrigerator. Note that this part may appear different than the original, but is an authorized manufacturer replacement.

$4.33

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, an...

$8.41

Hinge Bearing

Sold individually. Also known as a short door closing cam.

$100.41

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice i...

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with the clip, leads, and heat shrink. To access the defrost thermostat for this repair, you will need to remove your freezer shelves, as well as the back panel of your freezer. To complete this repair, you will need a 1/4-inch nut driver, a set of wire strippers and crimpers, and a heat gun or blow dryer. Before you begin this repair, be sure to disconnect the power source from the appliance.

$35.22

Door Shelf Bin

Sold individually. Sometimes referred to as the 2-liter bin.

$34.47

Evaporator Fan Motor Kit - 120V 60Hz

The evaporator fan motor circulates air through the food compartment for efficient cooling in refrigerators. The evaporator is located in the back of the freezer and it circulates the air over the refrigerator coils. The evaporator motor fan in your refrigerator should be replaced if the fridge section is too warm, the freezer section is too warm, orthe evaporator motor makes loud noises or stops working completely. The tools used for this repair are a 1/4 nut driver and wire strippers. *Please note: The motor has been updated by the manufacturer. Tip to detect if motor is not working, often if it fails it generates loud noises in the freezer area. For safety, make sure food is safely stored so it does not deteriorate while the power is off, and remember to unplug fridge.

$29.24

Run Capacitor

The run capacitor helps the compressor kick on and off while maintaining a constant temperature in your fridge and freezer. You may need to replace your run capacitor if your refri...

$29.07

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

$141.87

Ice Container and Auger Assembly

This assembly includes the auger and blades.

$42.48

Door Shelf Bin

Also known as gallon door bin.

$34.82

Door Bin

This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they are supported by the back of the shelf itself to the door of your r...

$31.27

Dispenser Crusher Housing

This dispenser crusher housing may also be known as a refrigerator ice crusher housing, and is compatible with your refrigerator. The function of the dispenser crusher housing is to shield the ice crushing blades within the ice container. To make this repair you will need a Phillips screwdriver, a flat blade screwdriver, a quarter-inch nut driver, and a pair of channel lock pliers. For this installation, work gloves are recommended. Note that this piece may look different or be a different color than the original, but this part will fit and function in the same way as the original part.

All Parts for the WRS3R3EWA
1-14 of 269