Models > WRS3R3EW4 > Instructions

WRS3R3EW4 Westinghouse Refrigerator - Instructions

All installation instructions for WRS3R3EW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS3R3EW4
496-510 of 517
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker quit making ice, clicking noise coming from lower rear of appliance

  • Customer: Paul from Cincinnati OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
If this happens to you the first thing I would do is shut off the freezer and, using a hair dryer, melt the ice in the ice maker and heat up the water inlet to make sure it is not froze up. Turn the freezer back on and wait to see if that cures the problem. If not, order the new water inlet valve and follow the simple instructions in the video provided on the PartSelect website. I have never have a more pleasant experience with any parts/repair service than I did with PartSelect. After ordering that part it came within the time they stated and their help with the install was great. Also helpful were the other customers talking about their problems and solutions.Thanks to PartSelect I now have Ice and a happy wife. Happy wife--happy life.

missing door bins

  • Customer: Cornell from Forest VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
These bins just snapped into place. very easy.

Quite making ice

  • Customer: Charles C. from Denver CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

not cold enough

  • Customer: Gary from Hudson FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section

filter pvc unit cracked ...water leaked

  • Customer: leon from kennett square PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
thought it was the o ring ...summer cottage thought i winterized everything ..ouch filter element cracked three screws a parts direct .com order ....1/4 inch nead screws nut driver or 1/4 inch ratchet ,,in and out and you can re=use the "push=lock" elbows

ice maker was not making ice, no water flow into.

  • Customer: Mary from Mt Pleasant PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

When I opened the door, sometimes the light was not turned on.

  • Customer: Helen from Burnsville MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
With the help of a knife we took out the light switch unplugged it, plugged in the new one and it started working.

the drive blade for ice maker was rusted

  • Customer: Michael from Philadelphia PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .

Broken shelves

  • Customer: Pamela from Brooklyn NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy to install (self explanitory)

frost build up in side on the back of the freezer .and my my filter housing cup crack due to ice build up inside .freezer side not to cold and fridge side to cold freezer and fridge side to factory settings

  • Customer: Carlos from Newton NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you

the ice auger, and ice crusher broke

  • Customer: Charles from Splendora TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just slide out the old part, slide in the new one, took less than 10 min

Door gasket was split.

  • Customer: ERIC from SAN ANTONIO TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy installation just pealed of the old door gasket and snapped in the new one the new gasket fitted perfect.No tools needed.

When the ice maker was filling the ice tray with water, the water would come out the water dispenser at the same time.

  • Customer: Greg from Murrieta CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

Wiring harness too thick to fit where the instructions told me to put it.

  • Customer: SHARON from Lynchburg VA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After trying several times to fit the wiring harness beside the ice maker without any success, I folded the wiring harness behind the ice maker. Between it and the back of the freezer.

ice crusher cylinder.

  • Customer: JoAnn from Davie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ice crusher cylinder broke (its plastic). I use a lot of crushed ice. I just ordered the entire drawer. It was just easier to just remove the old one and push this in. If one part goes then another will follow soon Works great.
All Instructions for the WRS3R3EW4
496-510 of 517