Models > WRS3R3EW4 > Instructions

WRS3R3EW4 Westinghouse Refrigerator - Instructions

All installation instructions for WRS3R3EW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS3R3EW4
466-480 of 517
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

refrigerator staying to warm

  • Customer: nicole from chipley FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
husband did it took only a few min part was easy to find

water valve leak

  • Customer: Donald from Wilmington NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.

broken suport for pam

  • Customer: JORGE from HOUSTON TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
take of the tray & take parts out & installed the new ones

No water and ice at Door Dispensor

  • Customer: hiroshi from Commack NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I figured out why no water and ice at door dispenser. Only a problem comes from a water supply valve. So I ordered parts assembly, and parts were arrived within 3 days. I replaced it, and then it worked OK since then. Regarding door shelf, it was cracked. So I replaced within 5 minutes. Anyway, I wanted to know when my parts arrive, so I called your Canadian operator, she was very nice. Just I want to say to manufacture of refrigerator, I wish they used batter parts. Because my refrigerator is less than two years old.

The door bins cracked.

  • Customer: Lori from Milwaukee WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old, slid in and pressed down the new, and that was it.

Refrigerator door "clicked" when opening.

  • Customer: Clinton from Conyers GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Removed the nuts on top - to loosen the door. Lifted the door off the hinge. Took out old part, put in new one, reinserted door, replaced nuts.

no problem

  • Customer: Frank from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pull the old one out and stick the new one in. Its just that simple.

Ice was not dispensing.

  • Customer: Sheree from New LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced ice container and auger assembly. (pulled the old one out and slipped the new one in) PROBLEM SOLVED! IT WAS SO EASY AND SO COST FRIENDLY! I LOVE TO FIX THINGS MYSELF AND THIS WAS REALLY EASY!

Water filter needed replacing

  • Customer: John from Port Saint Lucie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched video provided by website. Followed simple instructions.

Replace cracked water filter housing

  • Customer: Joseph from Cary NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Turn off water supply. Remove insulated cover (1/4" Nut driver) secured by 1 1/4" screw. Remove two 1/4" screws holding water filter housing in place on back o fridge. Noted the inlet and outlet water tubes and removed them from the housing using needle nose pliers (the elbows are removed by compressing the flange into the elbow while simultaneously pulling the tube in the other direction from the elbow). O-ring was placed in new filter cup. Plug filter into housing and screw filter cup onto the threads of housing. Insert tubing into new elbows, pressing them until they seat. Press other end of elbows onto nipples of filter housing, paying attention to the orientation noted above during dis-assembly. Attach filter housing to back of fridge with two 1/4" screws. Attach insulated cover over the housing with remaining 1/4" screw. Turn on the water supply and check for leaks. If no leaks, allow water to run through the system until all air is expelled.

Not enough storage

  • Customer: Lloyd from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We replaced our older 26' unit with a 23.6' model because of space limitations. There was no repair involved other than installing a new shelf with a cold cuts drawer and a 2 gal. door shelf bin. "Voila" more storage in the same space.

CH water filter

  • Customer: phillip from lexington KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out old replace new less than 5 min.

bearing would pop when open and close

  • Customer: Joseph from Hatboro PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took the door off and replaced bearing. easier than I thought it would be and no more popping!

Our refrigerator was not cooling below 50 degrees but the freezer had no problems. Turns out that the evaporator fan motor was dead.

  • Customer: Charles from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions in the video associated with the part that I ordered. The video was perfect and described everything I needed to do clearly. Repair is 100% successful!

Crisper support 'pin' for crisper broke off x 2

  • Customer: KENNETH from GLASTONBURY CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
1) cleared remaining parts of broken crisper supports by pushing them into refrigerator insulation(pushed on 'pegs' so 'peg' holes in side of plastic inner liner of refrigerator were clear. 2) Was unable to fully place new crisper supports into postiion. 3) Then, out of despiration, used small light hammer to gently tap on largest 'pin.' I was surprised to see this 'pin' enter into plastic side of refrigerator and then to see crisper support was secure when 'pin'/peg' was flush with new crisper support. 4) then returned crisper to correct postion; supports held. 5) WARNING-DO NOT OVERLOAD CRISPERS!! I BELIEVE THIS CAUSED 'PIN'/'PEG' FAILURE INITIALLY! I don't know if cause was volume too high with crisper forced into place OR if the crisper mass/weight was the culprit. SUGGEST weight limit less than 7.5 lbs.; don't attempt to load in more volume than top of crisper.
All Instructions for the WRS3R3EW4
466-480 of 517