Models > WRS3R3EW4 > Instructions

WRS3R3EW4 Westinghouse Refrigerator - Instructions

All installation instructions for WRS3R3EW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS3R3EW4
376-390 of 517
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water dispenser in door broke

  • Customer: Jean from Salem VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched a "how to repair" video on PartSelect. Everything went just as described until I realized that the actuator I was replacing had two tiny lights with wires attached. Perhaps I ordered the wrong part but it looked like the part I ordered would still fit but just not have the lights. I really didn't think it was necessary to have lights so I used scissors and clipped the wires so I could remove the old actuator. Then I continued to follow the directions in the video and now I have a perfectly functioning water dispenser. My husband was so proud of me! One additional tip- I found it was helpful to use a flashlight so I could see really well.

water leak

  • Customer: Forrest from Gulfport MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
two screws fingers pop the hoses off done in 4 minutes

The ice crusher housing is made of plastic and a piece of it broke off,

  • Customer: JAMES from COOSADA AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 4 screws to get the housing cover off. Remove the lock ring that holds the ice auger in place. REmove 4 screws to get the crusher housing off. Reverse the order to replace the housing. Very simple.

Door made a clicking sound when opening & closing

  • Customer: Bettie from Oxford GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Your video tutorial was great just did what it said to do. Your service in mailing parts was awesome. Thanks so much!

Broken crisper support and frame

  • Customer: William from Bremen GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had a little trouble getting old pin out of support bracket finally used screwdriver and broke plastic so I could get to the pin and used needle nose pliers to remove hanger then came right out putting new one in was a snap slid in tapped pin in and installed new crisper bracket took about 15to 20 minutes to complete.Contribute difficulty in removing pin to age of refrigerator had been in place for at least 5 years maybe longer overall experience not bad.I am 75 would probably been easier for a younger man more flexible.

Old one broke

  • Customer: Jacob from Dawson Springs KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the step by step video. I t was a breeze. Thanks for the fast service and number 1 video to show me how to install

Water dripped from water dispenser after use

  • Customer: Jeffrey from Greenfield MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

Three of the four drawer supports were broken

  • Customer: Linda from Turtle Creek PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It went okay. My husband did the job and he is handy. We both watched the little "How to" video and that was very helpful.

replace bearings in door

  • Customer: Lynn from Brunswick GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Had one other person, so putting the door back was easier. Repair went as told. Could do it myself.

Crisper support broke

  • Customer: Diana from Clearwater FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had to pry the old one from the cabinet. Had to work remaining piece evenly as to not crack the cabinet of the fridge. Not the best design on Frigidaire's part but it was fixable. Thanks for stocking every part under the sun.

Ice container and auger came apart after 13 years of daily use.

  • Customer: Peggy from Locust NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I simply pulled out the ice container and auger assembly and,after washing the new one, Iput the new one in and it worked immediately. It couldn't have been any simpler.

Rattling Noise from behind frig

  • Customer: Michael from Rockford MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.

Ice Maker stopped working

  • Customer: Charles from Fishkill NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Realized Ice Maker was not getting water during it's cycle and suspected water valve based on other posts to this web site. My fridge is 9 years old and the tubes connecting the valve were plastic screw on type. The new valve did not have threads to accept the nuts. Turns out all I had to do was cut the nuts off and insert the water tubes into the valve which auto-locked the tubes to the valve. Ice maker now works great.

lever was broke

  • Customer: James from Kersey CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
followed guide on enet.

ice maker was cycling, but no water was getting in

  • Customer: Donni from Houston TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!
All Instructions for the WRS3R3EW4
376-390 of 517