Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS3R3EW0 > Instructions

WRS3R3EW0 Westinghouse Refrigerator - Instructions

All installation instructions for WRS3R3EW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS3R3EW0
421-435 of 609
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Quit making ice

  • Customer: John from Norman, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed old ice maker by loosening two retention screws and disconnection the power connecting clip. Installed replacement ice maker using same retention screws, attached the power cord to existing connection. Total time to repair was less than 15 minutes. We now have ice again!!! This is the second part I have ordered from Part Select and each time the parts and delivery exceeded my expectations. Much easier than searching for these parts in your local appliance store. Thank you Parts Select.

The ice maker failed for the second time.

  • Customer: Russell from Detroit Lakes, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This is the 2nd ice maker replace in the past 20 months. This installation was easier following the experience of the first replacement. The instructions are well written. The pictures or illustrations are difficult. The most challenging part of the installation is routing and fastening the wire harness. The illustration was not helpful. Overall, this is a repair most DIYers should be able to accomplish.

Plastic Water Dispenser Actuator broke

  • Customer: Tom from Wheelersburg, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the lower section which just snapped out I went to remove the three screws on the bottom of the water/ice dispenser. The only problems I had we're here in that the screws were rusted and difficult to get out with water falling into this area over time. Then I easily removed the three screws holding the motor and actuator. Of course there was three more screws holding the water dispenser actuator in place. I took the broken piece out and put it all together again but placed some rust resistant screws I had to replace the three rusted screws. Works great!

just time to replace filter

  • Customer: Mary from Ness City, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
service was great-got filter promptly- on line instructions very helpful. showed how to turn off water, remove filter and replace with new one. no problems.

frig side freezing

  • Customer: Roberto from miami, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
checked web the termostat was given as 95% of cause purchased product, they sent thermostat . I changed it like instruction said this went well exceptthat was not the problem things still frooze. At least I tried the quick fix for 18$ which was not the problem. I called the tech wich told me parts and labor $330 damper /board plus labor which he said it's the problem. I agreed and will tell u the resuts. I tried but sometimes it's best left to the pros.

Broken blade on fan.

  • Customer: Deborah from Ridge Spring, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Used needle nose pleirs to slide the old fan off.Then slide the new fan on the spindle.The video really made this easy!

ice would not come out or crush

  • Customer: MAURICE from MEMPHIS, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
order ice container and auger assembly

ice maker not working and refrigerator too cold

  • Customer: John from Loxahatchee, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
ice maker= replaced overload,microswitch and solenoid water valves.refrigerator=replaced the thermostat.Great price on parts,very fast delivery and parts were a perfect fit.You made the job very easy. John

Frost on the ice maker/door

  • Customer: Janice from Shelton, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the ice maker cover on the front (6 screws)...took off old parts and installed new ones....very easy... replaced front cover and no more frost build up in the freezer.

Support Broken and would not support crisper

  • Customer: Robert from Columbia, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Because of the design of the support, this could have been a difficult job. However, with the video that was provided when I selected the part, it was not a problem. All you have to do is knock the center pin through the support and remove the old support. Pull the pin out of the wall of the unit and push the new support in and drive the new pin in until it is flush. That's it!

ice maker would not make ice

  • Customer: Gale from Scott, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 2 screws, unplug connector to remove broken ice maker. Plug replacement ice maker in, then screw in place with the two screws. It took longer to describe and type then it did to do the job.

Water filter housing mount

  • Customer: Thomas from Sisters, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Three very easy to get to 5/16" x 3/8" bolts to remove cover and mount. Elbows were tooless push to release type. Elbows removed in seconds from old housing. Elbows simply pushed on to nipples of new housing. Same three bolts to remount and done!

the filter cup had a hair line crack in it

  • Customer: Kerri from Spring Hill, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was so easy, i did it myself, also the help of a you tube video from Partselect. I was so proud of myself even though it only too less than 15 minutes to fix. Now no more wet towels laying around. thanks so much for your help.

Tabs that hang the crisper broke

  • Customer: Allen from Eagle, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordering replacement parts was easy! Expected a simple pull out old plug, insert new plug.... Not sure if it comes from factory like this or if this had been previously repaired poorly, but the broken plug was heavily glued in place. Took some serious finess work to remove without serious damage. Once out, it was simple plug in

No Water For Ice Maker Or Drinking

  • Customer: JAMES from ELLIJAY, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Repair as illustrated was right on. Repair was easy. No problem except still no water for ice or drinking. The valve was not the problem. Filter was replaced prior to valve replacement. Must be a electric switch some where. 3 Yrs ago I have replaced the water activation plastic lever for drinking which was a bit difficult and it turned out ok.
All Instructions for the WRS3R3EW0
421-435 of 609