Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS3R3EW0 > Instructions

WRS3R3EW0 Westinghouse Refrigerator - Instructions

All installation instructions for WRS3R3EW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS3R3EW0
406-420 of 609
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

icemaker not working

  • Customer: Philip from Sheridan, AR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first replaced dual solenoid, then ice maker. still not working. going to chase electrical next

Water dripped from water dispenser after use

  • Customer: Jeffrey from Greenfield, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

Three of the four drawer supports were broken

  • Customer: Linda from Turtle Creek, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It went okay. My husband did the job and he is handy. We both watched the little "How to" video and that was very helpful.

replace bearings in door

  • Customer: Lynn from Brunswick, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Had one other person, so putting the door back was easier. Repair went as told. Could do it myself.

Water was leaking in the back whenever the heating element turned on, freezing up the ice maker

  • Customer: Jose from Las Cruces, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Loosened the two screws on the side wall, disconnected the old unit. Reverse the order for installation. There is a small bracket at the botton that helps level the unit. Be sure to remove that bracket and put it on the new one.

Crisper support broke

  • Customer: Diana from Clearwater, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had to pry the old one from the cabinet. Had to work remaining piece evenly as to not crack the cabinet of the fridge. Not the best design on Frigidaire's part but it was fixable. Thanks for stocking every part under the sun.

Ice container and auger came apart after 13 years of daily use.

  • Customer: Peggy from Locust, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I simply pulled out the ice container and auger assembly and,after washing the new one, Iput the new one in and it worked immediately. It couldn't have been any simpler.

Rattling Noise from behind frig

  • Customer: Michael from Rockford, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.

Ice Maker stopped working

  • Customer: Charles from Fishkill, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Realized Ice Maker was not getting water during it's cycle and suspected water valve based on other posts to this web site. My fridge is 9 years old and the tubes connecting the valve were plastic screw on type. The new valve did not have threads to accept the nuts. Turns out all I had to do was cut the nuts off and insert the water tubes into the valve which auto-locked the tubes to the valve. Ice maker now works great.

lever was broke

  • Customer: James from Kersey, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
followed guide on enet.

ice maker was cycling, but no water was getting in

  • Customer: Donni from Houston, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!

ice maker not making ice

  • Customer: Bobby from Butner, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
problem still persists part did not fix problem. made repairs recommended per your site.

Blacks specs in ice cubes, lining deteriorating,

  • Customer: Robert from Hatteras, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair went exactly as illustrated by the video offered by part select. That video was helpful and showed me step by step how to accomplish the repair. The replacement part was exactly the same as the original, thank you part select.( Allow the old ice maker to return to room temperature before you remove the 1/4 nut securing the level mechanism, otherwise the frozen head of the not will break off).

Ice maker would not make ice or fill up

  • Customer: Brian from Louisville, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video instructions posted below the product. Its a tight area to work in but it can be done. It did not immediately start making ice. I waited and waited.... 3 hrs 4 hrs still not filling up or making ice. Finally I decided to pour some water in the tray and see if it would freeze ice and dump it. It did and immediately started to fill up on its own after that! Its been working perfectly ever since! So dont be alarmed if yours doesnt work immediately and try pouring some water in it if yours doesnt being working within several hrs. I am happy I was able to do this myself and save repair man costs. Its just not work the cost they charge for older appliances.

leak at one of the valves in the back of refrigerator

  • Customer: Ray from Westland, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Turned off the water supply ,pulled the plug removed two screws to access theater lines the new valve body was a little different than the original I had to cut off the end of each hose and push them in to the new connections the hoses are size and color coded replaced the two screws put the water line on plugged it in and turned on the water checked for leaks twice and replaced the back cover
All Instructions for the WRS3R3EW0
406-420 of 609