Models > WRS3R3EW0 > Instructions

WRS3R3EW0 Westinghouse Refrigerator - Instructions

All installation instructions for WRS3R3EW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS3R3EW0
376-390 of 519
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker stopped working

  • Customer: Charles from Fishkill NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Realized Ice Maker was not getting water during it's cycle and suspected water valve based on other posts to this web site. My fridge is 9 years old and the tubes connecting the valve were plastic screw on type. The new valve did not have threads to accept the nuts. Turns out all I had to do was cut the nuts off and insert the water tubes into the valve which auto-locked the tubes to the valve. Ice maker now works great.

lever was broke

  • Customer: James from Kersey CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
followed guide on enet.

ice maker was cycling, but no water was getting in

  • Customer: Donni from Houston TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!

ice maker not making ice

  • Customer: Bobby from Butner NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
problem still persists part did not fix problem. made repairs recommended per your site.

leak at one of the valves in the back of refrigerator

  • Customer: Ray from Westland MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Turned off the water supply ,pulled the plug removed two screws to access theater lines the new valve body was a little different than the original I had to cut off the end of each hose and push them in to the new connections the hoses are size and color coded replaced the two screws put the water line on plugged it in and turned on the water checked for leaks twice and replaced the back cover

Quit making ice

  • Customer: John from Norman OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed old ice maker by loosening two retention screws and disconnection the power connecting clip. Installed replacement ice maker using same retention screws, attached the power cord to existing connection. Total time to repair was less than 15 minutes. We now have ice again!!! This is the second part I have ordered from Part Select and each time the parts and delivery exceeded my expectations. Much easier than searching for these parts in your local appliance store. Thank you Parts Select.

Plastic Water Dispenser Actuator broke

  • Customer: Tom from Wheelersburg OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the lower section which just snapped out I went to remove the three screws on the bottom of the water/ice dispenser. The only problems I had we're here in that the screws were rusted and difficult to get out with water falling into this area over time. Then I easily removed the three screws holding the motor and actuator. Of course there was three more screws holding the water dispenser actuator in place. I took the broken piece out and put it all together again but placed some rust resistant screws I had to replace the three rusted screws. Works great!

just time to replace filter

  • Customer: Mary from Ness City KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
service was great-got filter promptly- on line instructions very helpful. showed how to turn off water, remove filter and replace with new one. no problems.

frig side freezing

  • Customer: Roberto from miami FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
checked web the termostat was given as 95% of cause purchased product, they sent thermostat . I changed it like instruction said this went well exceptthat was not the problem things still frooze. At least I tried the quick fix for 18$ which was not the problem. I called the tech wich told me parts and labor $330 damper /board plus labor which he said it's the problem. I agreed and will tell u the resuts. I tried but sometimes it's best left to the pros.

Broken blade on fan.

  • Customer: Deborah from Ridge Spring SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Used needle nose pleirs to slide the old fan off.Then slide the new fan on the spindle.The video really made this easy!

ice would not come out or crush

  • Customer: MAURICE from MEMPHIS TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
order ice container and auger assembly

ice maker not working and refrigerator too cold

  • Customer: John from Loxahatchee FL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
ice maker= replaced overload,microswitch and solenoid water valves.refrigerator=replaced the thermostat.Great price on parts,very fast delivery and parts were a perfect fit.You made the job very easy. John

Frost on the ice maker/door

  • Customer: Janice from Shelton WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the ice maker cover on the front (6 screws)...took off old parts and installed new ones....very easy... replaced front cover and no more frost build up in the freezer.

Support Broken and would not support crisper

  • Customer: Robert from Columbia SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Because of the design of the support, this could have been a difficult job. However, with the video that was provided when I selected the part, it was not a problem. All you have to do is knock the center pin through the support and remove the old support. Pull the pin out of the wall of the unit and push the new support in and drive the new pin in until it is flush. That's it!

ice maker would not make ice

  • Customer: Gale from Scott LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 2 screws, unplug connector to remove broken ice maker. Plug replacement ice maker in, then screw in place with the two screws. It took longer to describe and type then it did to do the job.
All Instructions for the WRS3R3EW0
376-390 of 519