Models > WRS3R3EW0 > Instructions

WRS3R3EW0 Westinghouse Refrigerator - Instructions

All installation instructions for WRS3R3EW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS3R3EW0
361-375 of 519
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice container and auger assembly broke apart

  • Customer: Sandra from Tulsa OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old container, opened the replacement, put it in and it worked perfectly. Great job! Arrived quickly, well packed and in perfect shape.

Ice door flapper broke in half

  • Customer: James from Atlantic VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed a video I found on how to take the front off of the ice dispenser ( to me the hardest part) Once I was in there it was a matter of removing the pin and spring,then putting the new flapper in place of the old. Hardest part in reassembling was getting the spring back where it belongs. After that it was a matter of putting the ice dispenser back together and testing. Works perfectly.

water dispenser in door broke

  • Customer: Jean from Salem VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched a "how to repair" video on PartSelect. Everything went just as described until I realized that the actuator I was replacing had two tiny lights with wires attached. Perhaps I ordered the wrong part but it looked like the part I ordered would still fit but just not have the lights. I really didn't think it was necessary to have lights so I used scissors and clipped the wires so I could remove the old actuator. Then I continued to follow the directions in the video and now I have a perfectly functioning water dispenser. My husband was so proud of me! One additional tip- I found it was helpful to use a flashlight so I could see really well.

water leak

  • Customer: Forrest from Gulfport MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
two screws fingers pop the hoses off done in 4 minutes

The ice crusher housing is made of plastic and a piece of it broke off,

  • Customer: JAMES from COOSADA AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 4 screws to get the housing cover off. Remove the lock ring that holds the ice auger in place. REmove 4 screws to get the crusher housing off. Reverse the order to replace the housing. Very simple.

Door made a clicking sound when opening & closing

  • Customer: Bettie from Oxford GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Your video tutorial was great just did what it said to do. Your service in mailing parts was awesome. Thanks so much!

Broken crisper support and frame

  • Customer: William from Bremen GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had a little trouble getting old pin out of support bracket finally used screwdriver and broke plastic so I could get to the pin and used needle nose pliers to remove hanger then came right out putting new one in was a snap slid in tapped pin in and installed new crisper bracket took about 15to 20 minutes to complete.Contribute difficulty in removing pin to age of refrigerator had been in place for at least 5 years maybe longer overall experience not bad.I am 75 would probably been easier for a younger man more flexible.

Old one broke

  • Customer: Jacob from Dawson Springs KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the step by step video. I t was a breeze. Thanks for the fast service and number 1 video to show me how to install

Water dripped from water dispenser after use

  • Customer: Jeffrey from Greenfield MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

Three of the four drawer supports were broken

  • Customer: Linda from Turtle Creek PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It went okay. My husband did the job and he is handy. We both watched the little "How to" video and that was very helpful.

replace bearings in door

  • Customer: Lynn from Brunswick GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Had one other person, so putting the door back was easier. Repair went as told. Could do it myself.

Water was leaking in the back whenever the heating element turned on, freezing up the ice maker

  • Customer: Jose from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Loosened the two screws on the side wall, disconnected the old unit. Reverse the order for installation. There is a small bracket at the botton that helps level the unit. Be sure to remove that bracket and put it on the new one.

Crisper support broke

  • Customer: Diana from Clearwater FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had to pry the old one from the cabinet. Had to work remaining piece evenly as to not crack the cabinet of the fridge. Not the best design on Frigidaire's part but it was fixable. Thanks for stocking every part under the sun.

Ice container and auger came apart after 13 years of daily use.

  • Customer: Peggy from Locust NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I simply pulled out the ice container and auger assembly and,after washing the new one, Iput the new one in and it worked immediately. It couldn't have been any simpler.

Rattling Noise from behind frig

  • Customer: Michael from Rockford MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.
All Instructions for the WRS3R3EW0
361-375 of 519