Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS3R3EW0 > Instructions

WRS3R3EW0 Westinghouse Refrigerator - Instructions

All installation instructions for WRS3R3EW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS3R3EW0
331-345 of 609
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken shelf support

  • Customer: Jerome from Hendersonville, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
ordered the part, watched the video....it was a snap

Light switch prevented door from closing.

  • Customer: Patrick from Penryn, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 5 people found this instruction helpful
The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!

Needed to replace water dispenser actuator

  • Customer: Dennis from Norman, OK
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
1. Turned off water and unplugged refridgerator. 2. Removed the drip tray. 3. Removed the 3 screws under drip tray. 4. Pulled facing off the fridge. 5. removed the 3 screws at top of dispenser. 6. Pulled the dispenser out far enough to remove broken actuator. 7. Removed 2 screws holding broken actuator in place. 8. Removed broken actuator and replaced with new actuator. Re-attached everything in reverse. Be aware that there are two serial numbers on the labels inside the refridgerator. The one with the letters at the end tells the color of the refridgerator. I had to return and reorder. The company emailed me the instructions and that went well too.

broken actuator arm

  • Customer: darlene from HESPERIA, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
take front panal off and unplug the electrectal tail to the front panal then unscrew the 4 hold down screws then take out broken part and then replace with new part and re-assemble front panal

Would not dispense ice

  • Customer: Dwain from Stamford, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
I replaced the entire dispenser. I decided it would probably be cheaper in the long run than replacing parts, thus lasting much longer. One thing I would like to comment regarding Part Select is that in all my years of ordering I have never recieved delivery any faster. I ordered one morning and part was delivered the next.

Ice maker leaked

  • Customer: Lisa from Orleans, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 3 people found this instruction helpful
Watched video. Followed steps exactly.

the refrigerator door was hard to close, and upon inspection I finally decided that the light switch was making the door hard to close.

  • Customer: Paul from Springfield, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 6 people found this instruction helpful
I removed the door actuated light switch with my index finger and thumb on my right hand. I then removed the two wires from the switch. I noticed that the new switch had different look to it,I think Frigidaire must have had a problem with the original design of the switch. Reassembly was just replacing the two wires and putting the new switch in place, and no more door closing problem.

ice maker stoped working

  • Customer: Jeffery from Robinson, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 3 people found this instruction helpful
Took less than 10 min to install following the inclosed instructions. At first it was not making enough ice to make me happy so I set the temp. a little colder in freezer. Now making ice like crazy. Works better than the old one ever did. Very happy with the new replacement.

Broken Refridgerator Door Handle

  • Customer: Debra from San Diego, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 21 people found this instruction helpful
It was really easy! Just snap off the trim above and below the handle, unscrew the old broken one, and replace it with the new one. Then snap the trim back on above and below the handle.
My husband wanted me to call a repair service to come out and take care of this. It would have taken two visits, the wait time in between, and the cost for the visits and the labor. I paid a bit extra to have overnight delivery and fixed it myself in less than 15 minutes! I will definitely use PartSelect in the future!

not making ice

  • Customer: mark from east greenwich, RI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 4 people found this instruction helpful
turned off water supply, removed cardboard back, removed supply line, unhooked all color coded connections,took out bad water valve and replaced with new one note: the new valve came with pex connections so i carefully cut off flared tubing ends with sharp razor knife making sure when i pushed tubing into new valve that i did so with some force until i HEARD and felt them snap in place very simple plus i received the new valve in 2 days very happy with PartsSelect.com you CAN do it

Water leaking from broken intake water line

  • Customer: Jamie from Weeki Wachee, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set, Wrench (Adjustable)
  • 0 of 4 people found this instruction helpful
Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.

broken water dispenser Actuator

  • Customer: Anthony from Sierra Madre, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 4 people found this instruction helpful
First I remove the water catch tray. Then I removed the three screws the hold the face plate on. ( You do have to slide face plate upward) I let that hang gently. Then I removed the three screws that hold the mother board in place, tilt the motherboard out to be able to see the back of the actuator. Remove three screws and flanges that hold actuator in place. Look at how spring is held in place before removing. Remove actuator, replace with new actuator set spring, replace screws and flanges, push motherboard back in place,replace the three screws,replace face plate with the three screws and replace catch tray. And your done!!!!

Plastic shelf support broke

  • Customer: Derek from Graham, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 4 people found this instruction helpful
Took out the support and put back in the new one.

Ice maker quit making ice

  • Customer: Wendy from Osceola, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 6 people found this instruction helpful
Replaced filter. Very quick shipping, was very happy to get is so soon.

wanted to change features

  • Customer: W from Lafayette Hill, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 10 people found this instruction helpful
Fridge came ice maker assy configured with an ice cream shelf to maximize space. I found this annoying becuase it blocked access to the ice maker controls and ice bin, which is useful for bulk access even thought there's a door front dispenser for ice. I recognized parts diagrams for a similar model and corrctly assumed they'd fit. So for $30 and an easy change I have the feature I wanted. Pretty cool.
All Instructions for the WRS3R3EW0
331-345 of 609