Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS26MR4JB6

WRS26MR4JB6 Crosley Refrigerator - Overview

Get Parts and Repair Help for WRS26MR4JB6

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS26MR4JB6, or you can search by name or part description. You can also find your part by where it is located on the WRS26MR4JB6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS26MR4JB6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.71

Door Bin

Door bins, also known as cantilever shelves, are storage bins located on the door of your refrigerator. Over time, a cold refrigerator can cause plastic to become fragile and break...

$3.92

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support and mounts to the inside cabinet wall. Replacing this part is an easy repair, but will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.

$31.02

Door Shelf

This white bin can also be used on the freezer/refrigerator door on some models. Sold individually.

$4.31

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. This part is made from plastic and mounts on the inside of the wall. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually.

$59.10

Water Inlet Valve

The water inlet valve is also known as the water inlet valve assembly and is compatible with your refrigerator. The function of this part is to release water from the supply line w...

$37.77

Door Bin

Gallon size. Sold individually.

$54.85

Upper Crisper Drawer Cover - Glass NOT Included

This cover holds up the top crisper drawer, and has drawer glides molded in it.

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with the clip, leads, and heat shrink. To access the defrost thermostat for this repair, you will need to remove your freezer shelves, as well as the back panel of your freezer. To complete this repair, you will need a 1/4-inch nut driver, a set of wire strippers and crimpers, and a heat gun or blow dryer. Before you begin this repair, be sure to disconnect the power source from the appliance.

$97.59

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice i...

$39.01

Crisper Drawer Cover - NO Glass

This part contains molded glide rails for the crisper pan. It does not come with the glass shelving. The glass is not included. Must be ordered separately.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Aged parts broken

  • Customer: Erik from Evans, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 654 of 678 people found this instruction helpful
After sitting in a cold refrigerator for year after year, plastic becomes brittle and breaks. This is what started happening to my shelves and door bins. The problem a lot of times is getting the right part since some of the parts do not have numbers.

This website gives a accurate description and best of all photos on an inch grid, so I can measu... read more

cracked, broken door bins

  • Customer: Beverly from Jackso, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 505 of 523 people found this instruction helpful
The new bins and I installed them in the door. Nice to have door space again. read more

Water in Frig was tasting bad.

  • Customer: Patricia from Fulton, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 489 of 490 people found this instruction helpful
I turned the cap for the old filter and pulled it out . Then I put in the new one in and turned the cap to secure it in frig. read more