Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS26MF8JS0

WRS26MF8JS0 Crosley Refrigerator - Overview

Get Parts and Repair Help for WRS26MF8JS0

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS26MF8JS0, or you can search by name or part description. You can also find your part by where it is located on the WRS26MF8JS0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS26MF8JS0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$36.84

Bottom Door Bin

This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they are supported by the back of the shelf itself to the door of your ...

$3.76

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support and mounts to the inside cabinet wall. Replacing this part is an easy repair, but will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.

$59.04

Water Inlet Valve

The water inlet valve is also known as the water inlet valve assembly and is compatible with your refrigerator. The function of this part is to release water from the supply line w...

$4.27

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. This part is made from plastic and mounts on the inside of the wall. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually.

$28.28

Meat Drawer Rail - Right Side

As you look into the fridge, this drawer support track is located on the right-hand side. This item is white in color and made of plastic. The drawer support track can wear out ove...

$53.89

Water Filter

Note: May need to order part # PS976499 to make water filter fit.

$53.74

Upper Crisper Drawer Cover - Glass NOT Included

This cover holds up the top crisper drawer, and has drawer glides molded in it.

$8.38

Hinge Bearing

Sold individually.

$29.15

Meat Drawer Rail - Left Side

This drawer rail supports the left hand side of the sliding drawer. The mounting screws are sold separately.

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with the clip, leads, and heat shrink. To access the defrost thermostat for this repair, you will need to remove your freezer shelves, as well as the back panel of your freezer. To complete this repair, you will need a 1/4-inch nut driver, a set of wire strippers and crimpers, and a heat gun or blow dryer. Before you begin this repair, be sure to disconnect the power source from the appliance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

yearly maintenance

  • Customer: Antonio from Folsom, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 588 of 615 people found this instruction helpful
swap filter read more

Tab on bottom door bin broke off

  • Customer: Mark from Redlands, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 516 of 534 people found this instruction helpful
Replaced bottom door bin being careful not to put stress on the tabs to fit into molded area in door. read more

Replaced door shelve

  • Customer: TERRI from STOCKTON, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 473 of 558 people found this instruction helpful
We live in rural SW Missouri, so I am very dependent on the internet. I found PartSelect on a Google search and simply inputted the modle number and serial number for the refrigerator and there it was. I was able to order the right part the first time and repair the refrigerator myself! No serviceman needed here! read more