Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
Below is a list of all parts for the Crosley Refrigerator WRS26MF5AWQ. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.
Door bins, also known as cantilever shelves, are storage bins located on the door of your refrigerator. Over time, a cold refrigerator can cause plastic to become fragile and break...
This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support and mounts to the inside cabinet wall. Replacing this part is an easy repair, but will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.
The water inlet valve is also known as the water inlet valve assembly and is compatible with your refrigerator. The function of this part is to release water from the supply line w...
Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. This part is made from plastic and mounts on the inside of the wall. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually.
Gallon size. Sold individually.
As you look into the fridge, this drawer support track is located on the right-hand side. This item is white in color and made of plastic. The drawer support track can wear out over time. The only tool required is a Phillips screwdriver. Empty out the drawer and remove it by sliding it forward. Lift out the shelf, remove the screw on the side of the shelf, remove the rail by pushing the rail forward and snapping out of place, insert new rail, and install the screw back in. Now the shelf can be put back into the refrigerator. The mounting screws are sold separately.
Note: May need to order part # PS976499 to make water filter fit.
This cover holds up the top crisper drawer, and has drawer glides molded in it.
If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with th...
This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice is automatically ejected and the process continues until the storage bucket is full. Your ice maker should be replaced if ice is not being generated, stored, dispensed, or the ice maker has been damaged. Replacing the ice maker is an easy job and only requires a 1/4 inch nut driver. Before you start this repair, make sure your refrigerator is unplugged. For help with this installation, check out the video below.
This part contains molded glide rails for the crisper pan. It does not come with the glass shelving. The glass is not included. Must be ordered separately.
The run capacitor helps the compressor kick on and off while maintaining a constant temperature in your fridge and freezer. You may need to replace your run capacitor if your refrigerator or freezer section will not start, if they are too warm, or if your refrigerator has become too noisy. Replacing the run capacitor is a relatively easy project. For this repair you will only need a 1/4 inch nut driver and needle nose pliers. Remember to disconnect the power and water supply line to the unit before you begin this repair. For full step by step instructions, simply click on the video below.
The screws and trims are NOT included with this handle.
Mounting screws NOT included.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.