WRS26MF5ASH Westinghouse Refrigerator - Instructions

What would have been a simple job I made hard by pulling the water hose out of its place that was the hardest part about putting the ice dispenser back in, it took me about thirty minutes to put it back I !

The website said 60% of people with same refrigerator problem solved the problem with a new fan kit. I received the fan kit within 3 days of ordering. Was shipped from Fresno, CA to Long Beach, WA. The fan kit was to be installed behind rear panel in the freezer compartment. When I removed the old fan motor, I noticed the shaft turned harder than the new fan motor, suggesting a problem with the old fan motor. I plugged in the obvious fan motor power bundle with no problem. The instructions and diagram with the kit nearly steered me wrong. Instructions, diagram and splices with the kit instructed to cut the "extra" wire bundle and splice "similar" wires (should have said same color wires). Luckily, I ignored those instructions when I remembered the U-Tube video depicted the extra wire bundle was to be inserted into a factory penetration in the back panel, facing the freezer compartment. This power bundle is for adding an ice maker, which my refrigerator did not have. When reassembled and the refrigerator restarted, I could immediately feel forced air in the refrig, where there was no flow before fixing. I observed that all the refrig and freezer dials do is act like a valve to increase or decrease air flow to the compartments. The dials have no mechanical or electrical connections, just designed to divert air flow from across the cold 'evaporator' fins. I recommend other consumers to remember carefully what they see in the video and watch again if stumped during the job. The video was better than the instructions which may have been written in China or India. I am happy. Repair was a lot cheaper than a new refrigerator and I would not have bought another Frigidaire. Thanks to this website. r. andersen

Part come in without delay - perfect fit - easy to install - works great

Open door - popped it in - done

pulled the old seals off one at a time and starting from the top of each door, pressed the top edge of the seal into the groove, using the quik clamps to hold the top in palce at each top corner, went down each side of the door and pressed the seal into the groove, when I reached the bottom, I moved the clamps to the bottom and used thm to help press the seal into the bottom groove, Each door took about 15 min.

I followed exactly the video instructions on your web site. They are perfect and simple.

Fixing the meat drawer slides was really easy and I got it fixed in a snap. What I wanted to tell you was that I ordered the wrong bins twice and your customer service person was just great she got me the wright bin and made returning the wrong parts very easy. I would like to complement her on her service.

Simply removed old bearing with the pliers and aligned new beating into the socket.

Just set the new shelf over the clips on the door. VERY easy.

followed the video and had little or no trouble loosening or tightening bolts or phillips head screws. The only difficulty was removing the spacer on the door itself. Otherwise a piece of cake. Good video and easy to follow instructions.

Turned off the refrigerator, removed the bottom drawer from refrigerator, then removed the glider bars for the drawer on the left side where the filter chamber is. Removed the filter and then removed the plastic peace guarding the filter chamber. Once that was all removed we removed the screws holding the filter base in place. Now that everything was exposed we removed the inlet and outlet lines from the filter base by pushing in the nobs inside the base and pulling the lines out with some slight elbow grease. After that we just proceeded in reverse. We plugged the filter in after the base was secure to make sure that the fix worked. The repair worked like a charm, was relatively simple and now our fridge is all better with water and ice without a large repair bill :o)

Replaced

The repair was very easy, just a matter of snapping the bin on the door. However, i was very please and impressed with the expeditious service that i received. I ordered the door around noon and it was delivered by 10am the next day. This is what i consider "quality service" and I thank this company sincerely.

All instructions included on this site are good. I would add only one thing to them. When removing the 4 water lines from the old unit be sure to pull up on the white rings while you pull down on the water lines. All else is a snap.

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water