WRS26MF5AQG Westinghouse Refrigerator - Instructions

The unit came with a wireing harnes.The only thing that was not the same was the ADC unit plug.thats why you replace it.take the cover off and replace one wire at a time, plug the new ADC in and replace covers.I should have gotten the fan and the thermostat at the same time.The fan was my problem

I guess it all started with stuffing too many jars into the bottom door shelf and before you know it, POP, the clips holding the shelf to the door break. Now super glue and/or epoxy just doesn't work as a repair for these types of breaks. So I ordered a new door from PartSelect. It was REALLY easy to find the right one with the pictures and the different views on their web site. I ordered the door and three days later it arrives. It took longer to get the new shelf out of the bubble wrap than it took to install. It just slid down and then snapped into place. Viola NEW Frige Door. Thanks PartSelect, I'll be back, when the next thing breaks.

I removed selfs,back covers. replaced wireing harnes on fan and hard wired the thermostat .very easy to fallow instuctions

Pull out the old clips,that were crack.The new ones are hanging off.I don'nt know if i should put some kind of glue,or something.To help it stick on.

I replaced the filter. However the ice cubes are very small and are being caught in the tines. Hopefully, once the filter gets more water through it, the ice cubes will be bigger. This is what happened the last time I replaced the filter.

Took the cracked bin out, put the new one in, simple as can be!

Removed the old gasket and installed the new one. Really, really easy to do. Took me about ten minutes.

So easy ... all I had to do was to snap the shelf into place - all of 2 seconds. The best part of the process was ordering the exact part I needed and how quickly it was received - awesome service. Thank you.

very easy just snaped shielf in

While the kids were getting ready for school in the morning they took a small break to help me. They balanced the door while I removed the old broken portions with needle nose pliers which took more time than everything else. I had the 1 philip screw and two hex screws removed and replaced in less than 15 minutes. The video was great because it confirmed what I already assumed.

just instilled some screws to the shelf to hold in please to give them more hold on to on the doors

took ice maker out empty ice removed 6 screws removed auger out took off lcck nut pulled off drum replaced with new drum reassembled.

I diagnosed the problem by checking the water flow at the supply valve and hose by disconnecting the hose from the back of the fridge. Found the pressure to be adequate. I then reconnected the supply hose and removed the cardboard backing from the fridge and removed the nuts holding the water inlet valve to the chassis. I loosened the first hose that runs from the bottom of the valve and had my wife activate the valve by pushing the water switch on the front of the fridge. Water basically sputtered out of the valve and I decided that was where the problem was. I ordered the valve from partselect. When it arrived I thought it was the wrong part because it had push-fittings whereas my original valve was all thumb screws. I took a chance and one by one used a utility knife to cut the hose free of the old valve as close to the nut as possible. Connecting them to the new valve was a piece of cake! Just make sure the hose bottoms out when you push it in. I turned the water back on, no leaks! Plugged the fridge in and pushed it back to the wall. After a bit of air bled out I had a strong flow of wateragain like new! The next day the ice cubes were solid again! We use the filtered water so many times a day and had been so frustrated with the slow water flow we had considered donating the fridge and buying a new one; thanks to this easy fix we expect keep it for years to come!

I did it just like the video it was that easy! love this web site amazing!

The repair was extremely simple. First i unplugged the fridge and removed everything from the door. I unscrewed the plastic cap on top of the fridge door hinge to expose the hinge. Then i unbolted the hinge it helps to have someonehold the door so it doesn't fall. After laying the door down I removed the rest of the broken hinge bearing inserted the new one and reinstlled the door making sure it was lined up evenly from top to bottom to the freezer door. The only thing that was annoying was i had to remove the metal plate at the bottom of the door to get to the broke off hinge bearing and those srews were square head screws not phillips head like the one on top of the door.