Models > WRS23W0AW9

WRS23W0AW9 Westinghouse Refrigerator - Overview

Get Parts and Repair Help for WRS23W0AW9

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS23W0AW9, or you can search by name or part description. You can also find your part by where it is located on the WRS23W0AW9 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS23W0AW9 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.76

Crisper Cover Support - Front

This part can be used for the front support. Sold individually and mounts to the inside cabinet wall.

Order within the next 9 hrs and your part ships today!
$3.84

Crisper Support - Rear

This part mounts on the inside of the wall. Sold individually.

Order within the next 9 hrs and your part ships today!
$6.93

Hinge Bearing

Sold individually. Also known as a short door closing cam.

Order within the next 9 hrs and your part ships today!
$29.64

Door Shelf Bin

Sold individually. Sometimes referred to as the 2-liter bin.

Order within the next 9 hrs and your part ships today!
$11.50

Defrost Thermostat Kit

This kit includes the clip, leads and heat shrink.

Order within the next 9 hrs and your part ships today!
$24.84

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

Order within the next 9 hrs and your part ships today!
$25.55

Water Dispenser Actuator

Once a glass is pressed against the actuator pad it will cause the dispenser to deliver ice or water when activated.

Order within the next 9 hrs and your part ships today!
$35.82

Door Shelf Bin

Also known as gallon door bin.

Order within the next 9 hrs and your part ships today!
$40.35

Evaporator Fan Motor Kit - 120V 60Hz

This kit includes the motor, clips and terminal connectors. This part has been updated by the manufacture. This evaporator fan motor is located in the back of the freezer, and cir...

Order within the next 9 hrs and your part ships today!
$101.76

Replacement Ice Maker

This part is the replacement heat-release ice maker unit only. This kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female and one round male connectors.

Order within the next 9 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Support studs were broken

  • Customer: Peter from Amherst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 191 of 196 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 171 of 211 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and no... read more

ICE MAKER STOPPED WORKING

  • Customer: JACK from MESA AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 84 of 90 people found this instruction helpful
IT WAS PRETTY STRAIGHT FORWARD. REMOVE THE TWO SCREWS THAT HOLD THE UNIT TO THE WALL OF THE FREEZER. IN MY CASE, I HAD TO USE A DIFFERENT ICE MAKER THAN WHAT CAME WITH THE FRIG. IN ORDER TO INSTALL THE REPLACEMENT UNIT THEY SENT A WIRE ADAPTOR SO IT WOULD ATTACH TO THE EXISTING WIRING. THAT TOO WAS ALL FINE AND DANDY. THE ONLY PROBLEM WAS THAT THE END O... read more