Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS23W0AW6

WRS23W0AW6 Westinghouse Refrigerator - Overview

Get Parts and Repair Help for WRS23W0AW6

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS23W0AW6, or you can search by name or part description. You can also find your part by where it is located on the WRS23W0AW6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS23W0AW6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.76

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support ...

$4.27

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. This part is made from plastic and mounts on the inside of the wall. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually.

$8.13

Hinge Bearing

Sold individually. Also known as a short door closing cam.

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with the clip, leads, and heat shrink. To access the defrost thermostat for this repair, you will need to remove your freezer shelves, as well as the back panel of your freezer. To complete this repair, you will need a 1/4-inch nut driver, a set of wire strippers and crimpers, and a heat gun or blow dryer. Before you begin this repair, be sure to disconnect the power source from the appliance.

$97.82

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice i...

$33.14

Door Shelf Bin

Sold individually. Sometimes referred to as the 2-liter bin.

$33.81

Evaporator Fan Motor Kit - 120V 60Hz

The evaporator fan motor circulates air through the food compartment for efficient cooling in refrigerators. The evaporator is located in the back of the freezer and it circulates ...

$27.78

Water Dispenser Actuator

Once a glass is pressed against the actuator pad it will cause the dispenser to deliver ice or water when activated.

$27.23

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

$103.77

Replacement Ice Maker

This replacement icemaker may also be known as the ice maker assembly and is compatible with your refrigerator/freezer. This assembly replaces the heat-release ice maker unit only. The kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female, and one round male connectors. The tools you will need in order to make this installation include a 1/4-inch nut driver, and a Phillips screwdriver. Before starting this repair make sure to unplug your refrigerator and shut off the water supply.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Support studs were broken

  • Customer: Peter from Amherst, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 262 of 273 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 231 of 277 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and no... read more

Broken ice maker

  • Customer: Juan from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 165 of 222 people found this instruction helpful
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice. read more