Models > WRS23W0AW3

WRS23W0AW3 Westinghouse Refrigerator - Overview

Get Parts and Repair Help for WRS23W0AW3

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS23W0AW3, or you can search by name or part description. You can also find your part by where it is located on the WRS23W0AW3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS23W0AW3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.84

Crisper Support - Rear

This part can be used for the rear support. Sold individually and mounts to the inside cabinet wall.

$3.12

Crisper Cover Support - Front

This part can be used for the front support. Sold individually and mounts to the inside cabinet wall.

$6.67

Hinge Bearing

Sold individually. Also known as a short door closing cam.

$11.50

Defrost Thermostat Kit

This kit includes the clip, leads and heat shrink.

$25.50

Door Shelf Bin

Sold individually. Sometimes referred to as the 2-liter bin.

$21.16

Water Dispenser Actuator

Black in color.

$20.66

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

$45.61

Evaporator Fan Motor Kit

This kit includes the motor, clips and terminal connectors. This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.

$31.99

Door Shelf Bin

Also known as gallon door bin.

$26.08

Door Bin

This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they are supported by the back of the shelf itself to the door of your refrigerator. Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Support studs were broken

  • Customer: Peter from Amherst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 156 of 161 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 127 of 161 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and no... read more

ICE MAKER STOPPED WORKING

  • Customer: JACK from MESA AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 73 of 77 people found this instruction helpful
IT WAS PRETTY STRAIGHT FORWARD. REMOVE THE TWO SCREWS THAT HOLD THE UNIT TO THE WALL OF THE FREEZER. IN MY CASE, I HAD TO USE A DIFFERENT ICE MAKER THAN WHAT CAME WITH THE FRIG. IN ORDER TO INSTALL THE REPLACEMENT UNIT THEY SENT A WIRE ADAPTOR SO IT WOULD ATTACH TO THE EXISTING WIRING. THAT TOO WAS ALL FINE AND DANDY. THE ONLY PROBLEM WAS THAT THE END O... read more