Models > WRS23W0AQ3

WRS23W0AQ3 Westinghouse Refrigerator - Overview

Get Parts and Repair Help for WRS23W0AQ3

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS23W0AQ3, or you can search by name or part description. You can also find your part by where it is located on the WRS23W0AQ3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS23W0AQ3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.84

Crisper Support

This support can be used for both front and rear and is sold individually.

$2.74

Crisper Cover Support - Front and Rear

This part can be used for either the front or rear support. Sold individually and mounts to the inside cabinet wall.

$6.67

Hinge Bearing

Sold individually. Also known as a short door closing cam.

$25.50

Door Shelf Bin

Sold individually. Sometimes referred to as the 2-liter bin.

$11.93

Defrost Thermostat Kit

This kit includes the clip, leads and heat shrink.

$20.66

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

$21.16

Water Dispenser Actuator

Black in color.

$31.99

Door Shelf Bin

Also known as gallon door bin.

$25.71

Dispenser Crusher Housing

This part may look different or be a different color than the original, but will fit and function the same as the original part.

$26.08

Door Bin

This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they are supported by the back of the shelf itself to the door of your refrigerator. Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Support studs were broken

  • Customer: Peter from Amherst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 136 of 141 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 116 of 149 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and no... read more

ICE MAKER STOPPED WORKING

  • Customer: JACK from MESA AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 66 of 69 people found this instruction helpful
IT WAS PRETTY STRAIGHT FORWARD. REMOVE THE TWO SCREWS THAT HOLD THE UNIT TO THE WALL OF THE FREEZER. IN MY CASE, I HAD TO USE A DIFFERENT ICE MAKER THAN WHAT CAME WITH THE FRIG. IN ORDER TO INSTALL THE REPLACEMENT UNIT THEY SENT A WIRE ADAPTOR SO IT WOULD ATTACH TO THE EXISTING WIRING. THAT TOO WAS ALL FINE AND DANDY. THE ONLY PROBLEM WAS THAT THE END O... read more