Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS23MW3AWD

WRS23MW3AWD Westinghouse Refrigerator - Overview

Get Parts and Repair Help for WRS23MW3AWD

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS23MW3AWD, or you can search by name or part description. You can also find your part by where it is located on the WRS23MW3AWD by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS23MW3AWD parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.93

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support ...

$4.19

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. This part is made from plastic and mounts on the inside of the wall. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually.

$8.17

Hinge Bearing

Sold individually. Also known as a short door closing cam.

$97.61

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice is automatically ejected and the process continues until the storage bucket is full. Your ice maker should be replaced if ice is not being generated, stored, dispensed, or the ice maker has been damaged. Replacing the ice maker is an easy job and only requires a 1/4 inch nut driver. Before you start this repair, make sure your refrigerator is unplugged. For help with this installation, check out the video below.

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with th...

$34.22

Door Shelf Bin

Sold individually. Sometimes referred to as the 2-liter bin.

$33.81

Evaporator Fan Motor Kit - 120V 60Hz

The evaporator fan motor circulates air through the food compartment for efficient cooling in refrigerators. The evaporator is located in the back of the freezer and it circulates ...

$28.41

Run Capacitor

The run capacitor helps the compressor kick on and off while maintaining a constant temperature in your fridge and freezer. You may need to replace your run capacitor if your refrigerator or freezer section will not start, if they are too warm, or if your refrigerator has become too noisy. Replacing the run capacitor is a relatively easy project. For this repair you will only need a 1/4 inch nut driver and needle nose pliers. Remember to disconnect the power and water supply line to the unit before you begin this repair. For full step by step instructions, simply click on the video below.

$26.19

Door Handle

The screws and trims are NOT included with this handle.

$28.16

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Support studs were broken

  • Customer: Peter from Amherst, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 277 of 288 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 233 of 279 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and no... read more

Broken ice maker

  • Customer: Juan from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 176 of 233 people found this instruction helpful
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice. read more