Models > WRS23MW3AWC

WRS23MW3AWC Westinghouse Refrigerator - Overview

Get Parts and Repair Help for WRS23MW3AWC

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS23MW3AWC, or you can search by name or part description. You can also find your part by where it is located on the WRS23MW3AWC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS23MW3AWC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.84

Crisper Support - Rear

This part can be used for the rear support. Sold individually and mounts to the inside cabinet wall.

$2.72

Crisper Cover Support - Front

This part can be used for the front support. Sold individually and mounts to the inside cabinet wall.

$6.67

Hinge Bearing

Sold individually. Also known as a short door closing cam.

$11.50

Defrost Thermostat Kit

This kit includes the clip, leads and heat shrink.

$25.50

Door Shelf Bin

Sold individually. Sometimes referred to as the 2-liter bin.

$19.35

Run Capacitor

This part is attached to the compressor. It helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$20.50

Door Handle

The screws and trims are NOT included with this handle.

$45.61

Evaporator Fan Motor Kit - 120V 60Hz

This kit includes the motor, clips and terminal connectors. This part has been updated by the manufacture. This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.

$20.66

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

$85.42

Icemaker Assembly

This icemaker is used on newer models where the cord will plug directly in to the back of the freezer. It includes the cover, fill cup, bail arm and a four-pin plug harness.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Support studs were broken

  • Customer: Peter from Amherst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 160 of 165 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 132 of 167 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and no... read more

bottom of fridg. would not get cool. Temp was 50-60degrees. The freezer compartment worked so I knew it was not the compressor.

  • Customer: Larry from Carthage NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 54 of 62 people found this instruction helpful
I removed the fan housing in the freezer section by removing all the screws. (7) There are two screws behind the vents. I did not have an ice maker to contend with so this was very easy. There is only two wires to disconnect....the ground wire and the electricity supply. Then you remove the unit from the back of the housing cover by removing two screws. Th... read more