Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS23MW3AQS

WRS23MW3AQS Crosley Refrigerator - Overview

Get Parts and Repair Help for WRS23MW3AQS

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS23MW3AQS, or you can search by name or part description. You can also find your part by where it is located on the WRS23MW3AQS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS23MW3AQS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.92

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support ...

Order within the next 10 hrs and your part ships today!
$4.31

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. This part is made from plastic and mounts on the inside of the wall. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually.

Order within the next 10 hrs and your part ships today!
$59.10

Water Inlet Valve

The water inlet valve is also known as the water inlet valve assembly and is compatible with your refrigerator. The function of this part is to release water from the supply line w...

Order within the next 10 hrs and your part ships today!
$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with the clip, leads, and heat shrink. To access the defrost thermostat for this repair, you will need to remove your freezer shelves, as well as the back panel of your freezer. To complete this repair, you will need a 1/4-inch nut driver, a set of wire strippers and crimpers, and a heat gun or blow dryer. Before you begin this repair, be sure to disconnect the power source from the appliance.

Order within the next 10 hrs and your part ships today!
$97.59

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice i...

Order within the next 10 hrs and your part ships today!
$34.22

Door Shelf Bin

Sold individually. Sometimes referred to as the 2-liter bin.

Order within the next 10 hrs and your part ships today!
$28.41

Run Capacitor

The run capacitor helps the compressor kick on and off while maintaining a constant temperature in your fridge and freezer. You may need to replace your run capacitor if your refri...

Order within the next 10 hrs and your part ships today!
$33.69

Door Bin

This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they are supported by the back of the shelf itself to the door of your refrigerator. Sold individually.

Order within the next 10 hrs and your part ships today!
$40.18

Door Shelf Bin

Also known as gallon door bin.

Order within the next 10 hrs and your part ships today!
$29.53

Dispenser Crusher Housing

This dispenser crusher housing may also be known as a refrigerator ice crusher housing, and is compatible with your refrigerator. The function of the dispenser crusher housing is to shield the ice crushing blades within the ice container. To make this repair you will need a Phillips screwdriver, a flat blade screwdriver, a quarter-inch nut driver, and a pair of channel lock pliers. For this installation, work gloves are recommended. Note that this piece may look different or be a different color than the original, but this part will fit and function in the same way as the original part.

Order within the next 10 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking out of refrigerator

  • Customer: Jose from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 455 of 523 people found this instruction helpful
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in p... read more

Support studs were broken

  • Customer: Peter from Amherst, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 269 of 280 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more

icemaker stopped making ice

  • Customer: David from New Bern, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 260 of 299 people found this instruction helpful
Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ... read more