Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS23MF5ASS

WRS23MF5ASS Westinghouse Refrigerator - Overview

Get Parts and Repair Help for WRS23MF5ASS

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS23MF5ASS, or you can search by name or part description. You can also find your part by where it is located on the WRS23MF5ASS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS23MF5ASS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.92

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support ...

$4.31

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. This part is made from plastic and mounts on the inside of the wall. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually.

$59.10

Water Inlet Valve

The water inlet valve is also known as the water inlet valve assembly and is compatible with your refrigerator. The function of this part is to release water from the supply line w...

$28.28

Meat Drawer Rail - Right Side

As you look into the fridge, this drawer support track is located on the right-hand side. This item is white in color and made of plastic. The drawer support track can wear out over time. The only tool required is a Phillips screwdriver. Empty out the drawer and remove it by sliding it forward. Lift out the shelf, remove the screw on the side of the shelf, remove the rail by pushing the rail forward and snapping out of place, insert new rail, and install the screw back in. Now the shelf can be put back into the refrigerator. The mounting screws are sold separately.

$53.89

Water Filter

Note: May need to order part # PS976499 to make water filter fit.

$8.38

Hinge Bearing

Sold individually.

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with th...

$97.59

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice is automatically ejected and the process continues until the storage bucket is full. Your ice maker should be replaced if ice is not being generated, stored, dispensed, or the ice maker has been damaged. Replacing the ice maker is an easy job and only requires a 1/4 inch nut driver. Before you start this repair, make sure your refrigerator is unplugged. For help with this installation, check out the video below.

$8.72

Closer Plate

$28.20

Water Dispenser Actuator

Once a glass is pressed against the actuator pad it will cause the dispenser to deliver ice or water when activated.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

yearly maintenance

  • Customer: Antonio from Folsom, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 588 of 615 people found this instruction helpful
swap filter read more

water leaking out of refrigerator

  • Customer: Jose from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 456 of 524 people found this instruction helpful
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in p... read more

Support studs were broken

  • Customer: Peter from Amherst, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 270 of 281 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers. read more