Models > WPRE6100G0WT > Instructions

WPRE6100G0WT General Electric Washer - Instructions

All installation instructions for WPRE6100G0WT parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WPRE6100G0WT
61-75 of 266
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water would not drain from tub.

  • Customer: James from Strafford NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 3 of 4 people found this instruction helpful
First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.

Would not pump out water

  • Customer: stephen from brooklyn MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 2 of 2 people found this instruction helpful
Wife put on the new part and she used a pair of plires and it was a little difficult to get her hand in the tiny spot but she put it on in less than 15 minuets and it is working great.

drain hose replacement

  • Customer: Henry from Merced CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Put the drain hose clip on (it will take squeezing but the hose will pass through). There will be a groove that whose width spacing is similar to the clip. Once that's on, insert hose and screw in the clip.

Debris in pump

  • Customer: Howard from Davie FL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 2 of 2 people found this instruction helpful
Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.

More and more was leaking water under the washer

  • Customer: W from Northbrook IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 2 of 2 people found this instruction helpful
It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

Leaking hose

  • Customer: Craig from Peabody MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Unscrew the 2 screws holding the drain hose clip to the machine - use bucket to get an excess water - remove bad drain line - I installed a new drain hose clip as well - make sure you put the clip on at the same position as the previous hose - push house firmly into opening and screw into machine - pretty easy repair - and I'm a novice

Pump was bad

  • Customer: Patrick from Clinton NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 2 of 2 people found this instruction helpful
I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

hose had a small pin hole. leaked.

  • Customer: Truett from Kennesaw GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

Drain hose was leaking

  • Customer: Mohammed from Berkeley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

Washer did not drain completely with water on floor, drain pump frozen.

  • Customer: Ray from Ventura CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 2 of 2 people found this instruction helpful
After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.

tub not spinning

  • Customer: dave from okeechobee FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
grab and yank off agitator ,used a socket to take off hub that covers hub nut and washer,took hub nut off and replaced tub bearing its a washer made of rubber and put new hub nut on pretty easy

Water leaking (from pump)

  • Customer: Jan from Protection KS
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 3 of 6 people found this instruction helpful
Ordered new pump on Sunday - replaced on Wednesday. Removed front washer panel with putty knife to release latches. Used pliers to disconnect hose clamps. Lots of paper towels to sop up water in bottom of washer and on floor. Unhooked electrical wires. Socket to remove pump. Reverse actions to replace pump. It's "plug and play"!

Two paddles on the agitator broke off.

  • Customer: Karen from Hamilton NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
After reading how others have done this and how easy it was, I decided to give it a try. And, sure enough, it was really easy. However, one concern I had was on lifting the old agitator off from the axle using both hands. I didn't want to have the agitator come crashing into my face as I pulled up. So I put a pillow on top of the agitator.

Washer wasnt draining properly, yet you could hear the pump turning.

  • Customer: Jeffrey from Syracuse NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Blowing hard into the drain hose would force the water off the impeller and allow the pump to reach proper speed to correctly drain. Start by unplugging the machine. To replace the pump, I simply removed the front cover of the washer. There are 2 clips to release along the top of the cover, then carefully pry forward and then lift it off the bottom clips. There are two wires which were a bit stubborn to remove. Carefully wiggle and pull with pliers, and be sure to note which one goes where. There were 2 bolts to attach the pump to the machine, which I removed using a 1/4" drive socket set, the size of the bolt head escapes me - on the small side anyhow. Also two squeeze clamps holding 2 hoses, which were easily removed using pliers. Pull the hoses and watch a pint to a quart of water dump out on the floor. Reverse the process to install. The hoses are tucked back in there, so you may want a flashlight to make sure you get the clamps back on correctly. Replace the front cover, and dont forget to plug the machine back in and you are ready to rock.

Washer not draining the water

  • Customer: Matthew from East Islip NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
1- Shut off water and unplug unit
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out

15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
All Instructions for the WPRE6100G0WT
61-75 of 266