Models > WPGT9350C0WW > Instructions

WPGT9350C0WW General Electric Washer - Instructions

All installation instructions for WPGT9350C0WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WPGT9350C0WW
1-10 of 10
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer would not drain

  • Customer: Joseph from SAINT JOSEPH MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 15 people found this instruction helpful
First I unplugged the washer. I removed the back of the washer and located the pump.I removed all the water from the pump, then I removed the hoses from the pump. I removed the wires from the pump and removed the two screws holding the pump in. I replaced the pump and reconnected everything. It works like new. The pump was the exact same thing ge sells but it cost a lot less.

The motor burnt out on the pump

  • Customer: CHRIS from DICKSON TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
Well replacing the pump went fine. I even did a trial run on a rinse and spin cycle and it worked great. Then i ran another cylce of clothes and walked away thinking all is well. Much to my surprise when I went to go through the utility room it was flooded. I did some inspecting and realised that I had put a hose on backwards. LOL. The good thing was that after I fixed the hose all worked well and haven't had any trouble since then. Your company was the cheapest price I found and the quickest delivery. Thank you so much for your help.
Sincerly,
Chris Lewis

Broken valve

  • Customer: Gayley from NASHVILLE TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 9 of 15 people found this instruction helpful
It was going to take my normal repair person at least 5 days to get the part. I ordered the part at half of what he was going to charge me (I did pay for the overnight shipping) and he installed it the next day.

Mice ate the drain hose

  • Customer: warsney from alpharetta GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 7 people found this instruction helpful
Looked under the washer and discovered a hole on the hose. Hardest part was to remove the damaged one. After that it was easy.

Went to the website and looked at the diagram and found the part. Ordered, received on time and put back in place. Unfortunately I discovered that another hose needed to be replaced. So I ordered a new one and hopefully everything will be up running by this weekend.

Extreme gear noise from broken coupling during spin rinsing

  • Customer: Dave from Port Orchard WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 5 people found this instruction helpful
Disconnect power and water lines. Lay the washer on it's back. Remove the nut (300) and washer (305). Rock the motor rotor (215) back and forth while pulling until it comes off the splined shaft. Remove the 3 bolts from the coupling assy (345). Remove the broken coupling (340) . Apply plastic grease to internal spline and gear teeth before reassembling in reverse of above. The machine is engineered to work on easily, however, I would not have needed to work on it if they had made the coupling assembly out of metal. The plastic gear fatigued at the internal spline and cracked apart after only 3.5 years of use.

Pulled out the internal comm cable plug

  • Customer: George from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Not repariable, ordered replacement and installed with no problems. Replacement was sent quickly.

Washer would not fill/Motor would not start

  • Customer: David from North East PA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 1 of 5 people found this instruction helpful
I tried troubleshooting this fault online but came up with some pretty scanty info. I replaced the sensor switch to no avail and while I was waiting for the inlet valve assembly, the GE rep showed up. He also did not have much in way of training/troubleshooting on the Profile Harmony washer. After 3 tries and numerous parts changes (motor, PCB, etc.) he, with help from another tech deduced that the stator was bad. Now waiting on the stator and hopefully will be fixed on Thursday, 11/8/07. Whew!

Machine displayed message that it had a problem.

  • Customer: Tracy from Ladson SC
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I knew the machine housing was making a bearing noise for sometime and then finally went out. Ordered the parts I was sure needed to be replaced. The dis-assembly started with removing the pulsator/agitator but would not come off after removing the bolt. Called a repair tech for advise and was told I would have to chisel the plastic ring that encapsulated the female spline hub of the pulsator/agitator. After removing the bulk of the pulsator, the hub would still not come off. Acquired a gear puller and applied to the hub but still would not come off. Then applied the gear puller and added the heat of a propane torch to the hub and the hub popped free. Removed large nut on the end of the machine housing/transmission assembly at the bottom of the tub. Put the washer on it's side, removed the rotor, stator, disconnected the clutch motor from the Machine housing/transmission actuator arm. Unbolted the machine housing/transmission and removed the assembly. Installed in the reverse order using Ceramic Anti Seize on all splines and female spline connections. Six hours later I was done. Had the manufacturer used some sort of Anti Seize the job would have only taken 1.5 hours tops.

Broken retainers on plastic pulsator cap.

  • Customer: GEORGE from ATLANTA GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced the broken cap, which would not stay in place on the pulsator, with the new one.

water valve had a crack and leaking .

  • Customer: RAJESH from MIAMI FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Repairs was real easy,first turn of power,and water supply,take of hoses,take screws of control pannel,remove pannel,then remove plastic sheild from over water valve,remove two screws from w/ valve,remove electrical,lift it out and replace it.
All Instructions for the WPGT9350C0WW
1-10 of 10