Models > WOS92EC7AW01 > Instructions

WOS92EC7AW01 Whirlpool Oven - Instructions

All installation instructions for WOS92EC7AW01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WOS92EC7AW01
1-8 of 8
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burned terminal block and filter board

  • Customer: Joseph from Decatur GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 31 of 69 people found this instruction helpful
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 14 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

oven temp wrong

  • Customer: Alan from Wallkill NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 5 people found this instruction helpful
Remove the oven door. Remove 3 self tappers on rear wall of oven to take off a round access panel. Pull out a pre-cut rectangle of insulation. Next I removed the 2 screws holding the sensor in place. Pulling the sensor out a bit told me I was "touching" the correct wires in the SMALL rectangular opening. The wires are not visable and 2 hands do not fit in this small opening.I looked at the NEW sensor to see the release on the sensor plug. Slip the angled needle nose into the opening and grasp the plug/release side. The plug pulled apart easily. The sensor wire pulls out with a little bit of twisting to fit it out the hole. The new plug pushes in and has to be worked down to where you can reach it. The same angled plier works to re-attach it. It takes longer to read this than to do the job. Best of luck, Al

oven had error messages

  • Customer: dan from Gallatin TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 2 of 3 people found this instruction helpful
I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 12 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Sensor went out after fire in oven fault code 1b11

  • Customer: patrick from Colleyville TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the 2 screws holding the sensor in the back of the oven and pulled the wires out. The connector got hung up in the insulation. Rather than pulling too hard, I loosened up the heating element plate and screws and pulled the whole plate out an inch or so so I could work the connector through the insulation. I forgot to shut off the power. When I put the sensor on, I got the same error. I briefly shut off the power at the breaker and turned it back on. The clock on the oven did not reset. It still didn't work. So I took the whole thing out, shut off the power, reconnected it, turned the power back on, reset the clock, and it worked! Should have turned the power off first and I wouldn't have had to do it twice.

Terminal block arc'ed because a wire had become loose.

  • Customer: Larry from Scranton KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

I had a power serge and it burned the Plug at the termial block and melted a few wire.

  • Customer: Robin from Vanderbilt PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
All Instructions for the WOS92EC7AW01
1-8 of 8