Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The original blower squirrel cage failed out balance.
Safety first , I shut off the circuit breaker . I removed the racks from inside the wall oven . I removed the the wall oven from the niche .Then removed the three sheet metal panels in the rear of the oven exposing the mounting screws that hold the blower down .I removed the wires from the blower motor and then the blower assembly ,then I removed the small duct affixed to the blower assembly by a single sheet metal screw and transferred it to the new blower assembly . I installed the adhesive backed foam strip that is a vibration dampener and reassembled in reverse order.Once the over was returned to its original position in the wall mounting I turned the breakers back on and tested the oven ...AAAAAAAAA++++++++++++ To be fair i must admit that I am not a novice at this 15 years of my working career revolved around HVAC and appliance repair ,still however a novice that is mechanically inclined can perform the same task in about 70 to 80 minutes as opposed to my 35 . That is all there is to it.
I removed all the screws attaching the inner liner to the door, then removed the broken glass. I did this before ordering the replacement glass so I could be sure that only one piece was broken -- the door contains four pieces of glass in all. After the replacement glass arrived (really fast delivery!), I cleaned all the parts and reassembled the door. I had some difficulty in aligning the screw holes properly, and I'm still not sure if I have the exterior sheet of glass positioned correctly -- the schematic shows the order in which the parts go together but not how they fit exactly. I should have inspected the door more closely before I took it apart. Anyway, it feels solid and everything seems to work.
Take door off completely by setting hinge locks into place and then removing door. Take all of the screws out from frame (remember that the flat screws go the outside and the raised heads on the inside of door)Remove the clips on the bottom of door as well. Carefully remove frame. Then remove the inner glass clips, this will allow you to remove the broke or cracked glass easily and install the new glass. Set the door on a soft towel with finish side down. Make sure your hinges are on the proper sides if you moved them. (you will see where the screw hole matches up with the bottom of the frame. Do everything in reverse to put back together. Good Luck
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
pulled out of wall. removed cover and visually checked for damage. saw none. saw what looked like a diode next to the control board. ohm meter showed open in both directions. from diagrams, determined the part to be a thermal fuse. replaced it, powered up. lights came on, set time, and turned the oven on. it started heated all seemed to work normally. noticed the fan was varing speed. pulled and oiled fan motor. appears to have smoothed out. i suspect the fan wasnt moving enough air to keep the electronics area cool. ran for 30 minutes at 350 deg. appears to be ok. time will tell if there is another problem i havent found.
Sorry but that would take too long to give all instructions, but I will mention that there were four glass plates if you count the cover of the door which is a large glass piece. All glass plates had to be taken out or off including the holder hardware in order to get to the inner glass (about 15 screws in all). No you-tube videos seemed to apply directly for this door. Taking some pics and using a card to hold screws in the pattern they were taken out helped keep the in order to be replaced (I screwed the screws into a paper sheet to keep the pattern with some labeling like top, bottom, etc). Lower glass door appears to only have two glass plates (didn't take it apart, but inner glass holders were not seen when peering in through the inner glass as they are in the upper door). If the inner glass plate on this door gets broken it should be easier. The glass was broken for some time before this repair so there was a lot of cleaning required inside the door. Oh, by the way, when taking out the door off pull out (not up) after locks are released and when the door is mostly closed. Push back in and open door down a bit to lock back in place. This is far from complete but I hope it helps some.
F1E1 error occurred during and after using the oven, getting more frequent
turn off power. Remove trim from sides of oven- screws inside lower doors, then pull off trim from bottom - may need scraper to pull out bottom. Remove screws holding oven into opening - 2 along each side. slide oven out of opening about 12-15" - have a wood block or something else to support the weight of the front of the oven ready before pulling out. Remove 2 screws from side of control panel. Remove screws from top cover of oven to access control board. Control panel pulls off, but is a little tight. Ribbon cable is connected, so do not force it. Pull out the bottom edge of the control panel and lift to allow the top to be pulled off. Leave control panel hanging on front. Once top is off, control board is right there. Confirm that the new board looks like the old one - same connectors, etc. Remove the connectors from the board. Take a picture or label them before removing. Some connectors needed a little help from the scraper to release from the socket. Remove 2 screws holding the board - one at each end. Replace with new board and plug cables back in. Replace cover and control panel in reverse of removal, slide back into opening, screw to opening. Replace trim and screws. Turn on power and confirm it works.
GENERAL APPROACH: 1) Checked YouTube for some general guidance: VERY helpful things there for this! PartSelect's install info. was helpful as well- Thank you for this! 2) had table set up in order to disassemble the door once it was removed 3) There are 4 separate glass panes in there- they all need to be cleaned 4) TOOK PICTURES AND MADE CAREFUL NOTES AS (12 or 15?) SCREWS ARE TINY & THERE ARE DIFFERENT TYPES. TAPED THEM NEAR WHERE I REMOVED THEM SO AS TO KEEP THINGS STRAIGHT 5) Like any project little or big, just take your time & it actually works out well 6) take advantage of this downtime to clean the oven good, as well as the door & panes of glass. Cleaning was 75% of this project. 7) EXTRA: If you're so inclined, turn the breaker off for the Oven & carefully remove the lower heating element to enable easier & more thorough cleaning of your oven. You'll be glad you did this- and so will your cook!
The oven door would not open properly. The hinges needed replacement.
I followed the instructions per a YouTube video. My older model was slightly different in parts used in the video, but the general idea was the same. Very happy with current repair / parts. The door now opens smooth as glass, and I even got a chance to clean some internal parts inside the door.
Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.
Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.
Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.
