Models > WM3677HW > Instructions

WM3677HW (ABWEEUS) LG Washer - Instructions

All installation instructions for WM3677HW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WM3677HW
46-59 of 59
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Hot Water Inlet valve (solinoid valve leaking)

  • Customer: MARVIN from MARYVILLE TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

Washer not spinning and giving error message OE

  • Customer: Allan from Virginia Beach VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

would not pump the water dry

  • Customer: Jinjer from Colorado City AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
greate very easy and the parts fit awsome the shiping was fast and easy very satified

OE CODE - The washer machine would not drain

  • Customer: Gustavo from Ukiah CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the bottom left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.

Drain water was not being fully pumped out, leaving foul water in the tub and wet clothes smelling like sewage.

  • Customer: Myles from Kingston NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!

Washing machine was leaking

  • Customer: Rod from Camano Island WA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Contacted LG customer service, not much help there. Watched a very helpful Utube video on how to find and repair the leak. The video suggested that the most common leak is in the drain hose with bellows. Removed the rear panel and removed the bellows unit using pliers for the clamps and screwdriver for the bellows part. This was pretty easy. The rubber bellows was leaking in the exact same place as the youtube video showed. This is a Design Flaw that LG needs to fix. Ordered the new part and installed the bellows portion of the part first, as the angle for that installation needs to be correct. Then attempted to install the end of the hose (very inaccesible) to the pump drain. Very difficult to position the factory supplied spring clamp with pliers so I purchased a screw-type clamp (using the nut-driver rather than a screw-driver to tighten the clamp was helpful) at the local hardware store and that made my job much easier. Note: My unit is mounted on a pedestal, so it was a little easier to access the part location (about one foot off the floor, rather than at floor level), but it may be that the part should be replaced from the bottom of the unit, which would make it much easier to access. Then I installed the other end of the hose to the drain line using a screw-type clamp. I am 69 years old, and not that flexible anymore, so getting down on the floor to reach inside the unit was difficult. You need patience to do this job and you have to make sure all the clamps are properly installed so you don't start the machine up and end up with another leak. For me, this process was difficult and took more than two hours to complete. Limited access to the area made it more difficult and I hate the factory clamps they use. Overall, the repair costs about $25, compared to the $125 just to come look at the machine, then more money to fix the unit. It was satisfying to complete the repair for a small amount of money, but not sure it was worth the aggravation.

Water was leaking out the bottom

  • Customer: Andrew from San Mateo CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the manufacturers instructions to disassemble the washer from the top. There was a video on youtube of a guy who was able to replace his bellows hose from the back, but maybe my arms weren't long enough, I couldn't reach all the way to the front. The washer was pretty easy to take apart, except for taking off the top, where there were 2 extra screws not mentioned in the instructions. Replacing the part was really easy. HERE'S THE MOST IMPORTANT PART: LG DOESN'T MENTION IT IS REALLY HARD TO GET THE CLAMP ASSEMBLY BACK ON THE GASKET WITHOUT A SPECIAL TOOL. You can buy the special LG tool, or you can do what I did (and others on the internet) and buy an $8 "Brake spring spreader" tool at your local auto parts store. Repair was a success. No more water leaking!

noisy during spin

  • Customer: paula from port st. lucie FL
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
disasemble the whole mashine... split outer tank...pound out old bearings... press in new... reassemble.... look for leaks... repair man estament..$900...cost me less than 100.. took 4 hours

door would not lock

  • Customer: Eileen from Allen Park MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used a screwdriver to carefull lift the top of washer. Reached in and unplugged old assembly from wir harness. Unscrewed old one (2 screws) from washer screwed in new one connected it to wire harness. Closed top of washer and plugged it in and it was ready to use. I am a 53 year old female and had never done this before. The repair shop wanted $150 to install part plus the part cost more from them. I' m sure a guy could do the job in 15 minutes or less.

water leaking fromdoor

  • Customer: Walter from Deland FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
remove the front part of the machine to get to the door hinge.

Bearings were shot

  • Customer: Jean from Tolland CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Took apart the washer and removed bearings and shaft on spider. My advice would be to order the spider and shaft (one piece) hen ordering the bearings, seal, and tub gasket. If the bearings are gone, it is likely the shaft is gone too as mine was.

blown out front and back bearings on front loading washing machine

  • Customer: MICHELLE from FLORENCE WI
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
took lid off of washer (slides back, not pry) and had to dismantle from springs, rubber around door and pistons on bottom. also had to disconnect from electrical plugs and took out dispenser drawer and all hoses. also have to take off magnetic piece devices from off back of drum. mark everything before dismantling with a black permanent marker so you will know what went where when putting back together and what pieces were facing up,top, etc. once get everything freed up, entire tub pulls up out of the washer. get old shot bearings out of drum, but be careful not to beat on it too much so that you don't damage the shaft or "oblong" the tub, etc. ordered parts that arrived in about 2 days. to put new bearings back in, get large washers -one for front and one for back -same size as the bearings so you will have equal pressure coming from front and back, put a long bolt thru the holes in the bearings with one of the large washers on each end. put a nut on the end of the bolt and begin to tighten. this will pull the bearings together back into their positions without ruining them and gives you equal pressure all around. be careful when you get them tight, they will fit snugly back into place. put it all back together carefully, just like you took it apart. if you labeled everything, you should have no problem putting the puzzle back together. before putting the tub pieces back together, i ran a bead of silicone caulk to prevent leaks. started it back up and runs great! fixed it for total of $72 (including shipping charges), which is a lot cheaper than buying a new washing machine. it is tedious and somewhat challenging, but if you are in any way mechanical, you shouldn't have any problems.

The washer kept displaying "tE" error and the machine would stop.

  • Customer: William from Edgewood MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
First we unplugged the machine. Then turned off the water and disconnected the hoses. Pulled out the machine and laid it on its side to access the themsistor located on the drum. (No, you do not have to remove the control panel at all to replace this part) The thermsistor is clearly seen with a flashlight. There were plastic ties holding the wires of the thermsistor so we used small scissors to cut the ties. Then unplugged the old thermsistor and plugged in the new thermsistor and used a regular bag twist to secure the wires. Repair complete and the machine is back to normal. Thank you Part Select.

Humming, no error code, not spinning

  • Customer: Brian from Camden MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.
All Instructions for the WM3677HW
46-59 of 59