Models > WM3431HS (WM3431HS /00)

WM3431HS (WM3431HS /00) LG Washer - Overview

Get Parts and Repair Help for WM3431HS

If you know the washer repair part you need, you can browse the list of all parts on the WM3431HS, or you can search by name or part description. You can also find your part by where it is located on the WM3431HS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$53.71

Drain Pump and Motor Assembly

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. Note: Pump casing is not included.

Order within the next 3 hrs and your part ships today!
$17.52

Water Inlet Valve - Hot

Order within the next 3 hrs and your part ships today!
$22.86

Tub Bearing

Sold individually.

Order within the next 3 hrs and your part ships today!
$34.68

Tub Bearing

Order within the next 3 hrs and your part ships today!
$8.18

Gasket

Order within the next 3 hrs and your part ships today!
$1.95

Locking Pin

The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.

Order within the next 3 hrs and your part ships today!
$12.91

Shock Absorber

Sold individually.

Order within the next 3 hrs and your part ships today!
$1.95

Cap,Drain Hose

Order within the next 3 hrs and your part ships today!
$1.95

Clamp

Order within the next 3 hrs and your part ships today!
$40.25

Noise Filter Assembly

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing maching wouldn't drain

  • Customer: Jorge from Apple Valley CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 199 of 259 people found this instruction helpful
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just... read more

Unit would not start up

  • Customer: LES from GAINESVILLE FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old no... read more

Washer will not power on

  • Customer: Robert from Damascus MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power. Removed washer top; only 2 screws in back. Disconnected two wire connectors on Filter Assembly Circuit. Removed assembly; 1 screw. Installed new assembly, reconnected wires, and replaced washer top. read more