Models > WM2487HRMA > Instructions

WM2487HRMA (ACREEUS) LG Washer - Instructions

All installation instructions for WM2487HRMA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WM2487HRMA
16-30 of 64
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

noisy during spin

  • Customer: paula from port st. lucie FL
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
disasemble the whole mashine... split outer tank...pound out old bearings... press in new... reassemble.... look for leaks... repair man estament..$900...cost me less than 100.. took 4 hours

door would not lock

  • Customer: Eileen from Allen Park MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used a screwdriver to carefull lift the top of washer. Reached in and unplugged old assembly from wir harness. Unscrewed old one (2 screws) from washer screwed in new one connected it to wire harness. Closed top of washer and plugged it in and it was ready to use. I am a 53 year old female and had never done this before. The repair shop wanted $150 to install part plus the part cost more from them. I' m sure a guy could do the job in 15 minutes or less.

water leaking fromdoor

  • Customer: Walter from Deland FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
remove the front part of the machine to get to the door hinge.

Bearings were shot

  • Customer: Jean from Tolland CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Took apart the washer and removed bearings and shaft on spider. My advice would be to order the spider and shaft (one piece) hen ordering the bearings, seal, and tub gasket. If the bearings are gone, it is likely the shaft is gone too as mine was.

blown out front and back bearings on front loading washing machine

  • Customer: MICHELLE from FLORENCE WI
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
took lid off of washer (slides back, not pry) and had to dismantle from springs, rubber around door and pistons on bottom. also had to disconnect from electrical plugs and took out dispenser drawer and all hoses. also have to take off magnetic piece devices from off back of drum. mark everything before dismantling with a black permanent marker so you will know what went where when putting back together and what pieces were facing up,top, etc. once get everything freed up, entire tub pulls up out of the washer. get old shot bearings out of drum, but be careful not to beat on it too much so that you don't damage the shaft or "oblong" the tub, etc. ordered parts that arrived in about 2 days. to put new bearings back in, get large washers -one for front and one for back -same size as the bearings so you will have equal pressure coming from front and back, put a long bolt thru the holes in the bearings with one of the large washers on each end. put a nut on the end of the bolt and begin to tighten. this will pull the bearings together back into their positions without ruining them and gives you equal pressure all around. be careful when you get them tight, they will fit snugly back into place. put it all back together carefully, just like you took it apart. if you labeled everything, you should have no problem putting the puzzle back together. before putting the tub pieces back together, i ran a bead of silicone caulk to prevent leaks. started it back up and runs great! fixed it for total of $72 (including shipping charges), which is a lot cheaper than buying a new washing machine. it is tedious and somewhat challenging, but if you are in any way mechanical, you shouldn't have any problems.

Humming, no error code, not spinning

  • Customer: Brian from Camden MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.

Washer drum slipped during spin cycle

  • Customer: Alan from Elmwood Park IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Opened rear compartment of washer and observed problem with drum shaft slipping inside of plastic motor assembly. The plastic teeth used to secure drum shaft were worn down. The part I needed was sent as an assembly but should have been sent separately for a much lower cost? The new part looked like it was of a sturdier design. All in all I saved hundreds of dollars repairing the washer my self. The woman I spoke to on the phone was really nice and very helpful.

Leaking Hot Water Intake Valve

  • Customer: Thomas from Commack NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

Will not start after dorr is closed. Shows Code dE. Door locks properly, two clicking is heard before code shows up.

  • Customer: Juan from Anaheim CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.

My Washing Machine was not draining properly

  • Customer: matt from Fuquay Varina NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

slow water leak

  • Customer: mark from pleasant prairie WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

Noisy Bearings

  • Customer: Gary from Pine AZ
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
In order to replace the bearings of a front loader LG Washer you will need to disassemble the entire unit. you should have excellent mechanical skills to tackle this project with necessary tools. Plan on replacing both bearings and rear seal, also plan on replacing the spider and drum seal. The Spider that supports the inner drum will be corroded due in part to seal failure. By the time you are hearing the bearing noise the damage to the spider will have taken place and need replacing. You can watch a few videos on youtube with similar appliances to give you an idea of the project at hand. Once disassembled cleaned and inspected the assembly goes real smooth. The washer now works as good as new and is ready for another 10+ years of service. Doing this project myself has saved me from buying a new one and that savings amounts to over $1000 bucks. LG washers are built to last and you will see that while working on it! Good Luck and do your homework!

Water will not Drain

  • Customer: Nate-Talisha from Miramar FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
took out the drain pump and replace with a new one

Increasingly noisey while on spin cyle

  • Customer: Craig from Pisek ND
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Disconnected power. Removed washer top, upper front control panel, and front panel. Removed hoses from washer drum housing. Removed cabling and support springs and stabilizers. Removed drum housing from cabinet. Removed bolts that secure the two halves of housing. Removed rotor from drum shaft. Removed stator from housing. Supported drum housing and with hammer and punch, removed drum shaft from bearings. Replaced bearings and seal and reassembled in reverse order.

my lg washer wasnt draining

  • Customer: chris from glenwood springs CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful
All Instructions for the WM2487HRMA
16-30 of 64