Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WJRR4170G0WW > Instructions

WJRR4170G0WW General Electric Washer - Instructions

All installation instructions for WJRR4170G0WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WJRR4170G0WW
61-75 of 363
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drain hose had a hole in it

  • Customer: kartik from radnor, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 4 of 4 people found this instruction helpful
used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

some leak

  • Customer: Roberto from Nokesville, VA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 4 of 4 people found this instruction helpful
First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Dial Spins Too Freely

  • Customer: STEPHANIE from Bluefield, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
The grooves on the bottom of the control knob were worn away. I just pushed the timer knob clip off of the underside of the knob, removed it from the washer and put the new knob on and put the clip back on. It was a piece of cake!

Very noisy in spin mode

  • Customer: James from Colora, MD
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 5 of 8 people found this instruction helpful
a) remove front panel by depressing the 2 clips at the top in line with the lid b) remove the lid switch and 2 screws holding top on and remove top by tilting up SLIGHTLY and sliding to left. c) Remove agitator and by pulling straight up on it and remove adapter underneath d)remove 4 bolts holding 4 rubber straps to top of tub assembly, readily visible when top is removed. e) unplug motor wiring and disconnect pump and bleach hoses from tub f)while lifting up on tub, push down on each of the 4 suspension rods and disconnect them at bottom of tub ( this is the most difficult part, and to make it easier disconnect the rear rods first) g) tilt tub forward and remove tub assembly h) NOW, for the big nut that holds the spin basket in-- #1, it is LEFT HAND THREAD, so you will turn it to the right to remove it. #2, it is VERY TIGHT and requires a 1&11/16" spanner wrench (which I did not have) for removal. Instead, I used a 1&11/16 socket, an extension and an air impact wrench to remove and replace the nut. Assembly is reverse of removal and remember, that nut is ALUMINUM so be careful with that impact wrench when tightening it back up!I replaced the nut and split ring and cleaned the whole area thoroughly, and it greatly reduced the noise in spin mode. I did not replace the metal housing on the bottom of the spin basket, because it was $50 bucks. this probably would have eliminated all the noise, but my repair only cost $19 in parts, including shipping ,and the parts arrived in 1 day.

Leaking hose

  • Customer: Craig from Peabody, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Unscrew the 2 screws holding the drain hose clip to the machine - use bucket to get an excess water - remove bad drain line - I installed a new drain hose clip as well - make sure you put the clip on at the same position as the previous hose - push house firmly into opening and screw into machine - pretty easy repair - and I'm a novice

Water leaking from filler hose outside of tub

  • Customer: Paul from Talihina, OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 8 people found this instruction helpful
removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.

drain hose cracked, leaking water, when in use

  • Customer: patricia from Merced, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 4 of 5 people found this instruction helpful
It was easy, I just removed the old drain hose clip with a screwdriver. Next, removed the old, cracked hose, inserted the new one, and screwed the new clip in.
The best part about this story is the incredible service I was given, by this company. I bought the machine at Sears, so I assumed I could find the hose their. No, they instructed me to go to Orchard Supply(their sister store), I purchased a drain hose, the clerk told me to buy, but the water was still leaking. So, I went on-line and found the right hose, and now I will continue to purchase what I ned for my machine from your company. REALLY Fast Service. Thanks

the hose extension had a tear

  • Customer: Jennifer from Concord, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 4 of 5 people found this instruction helpful
First I removed the screws that held the drain hose clip to the washer. Then I pulled the hose, along with the clip, completely out of the washer. I then took the old hose out of the washer clip and put the new hose in the new clip; I pushed the hose into the washing maching and tightened the hose clip to the maching with the existing screws. Seriously easy, took less than 15 minutes. And I have virtually no handyman skills at all!

Washer wouldn't spin, repairman said replace transmission.

  • Customer: Justine from Cardiff, CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 4 of 5 people found this instruction helpful
Pretty much the entire machine has to come apart to replace a transmission. The thing to know that no one mentioned is that the hub nut is reverse threaded - that means righty loosey.
Even if I had known, I tried it both ways and I doubt I could have gotten it off without the chisel as the others also had to do. Split ring was also frozen in place by hard water and soap scum so had to break that cheesey piece of aluminum off also. If you are taking apart your washer, I advise ordering these 2 parts so you will have them after you destroy the old ones trying to get to the part you need to fix.

Thanks to parts select for the exploded diagram!

Water was leaking from the tub to the floor.

  • Customer: Nolan from Fort Polk, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 5 people found this instruction helpful
First I removed the two clamps that hold the inlet drain hose onto the pump. **There may still be water in the hose** This was pretty easy, but a set of vice grips would have been nice. The space is not too cramped, but required a little bit of wiggling. Putting it on was a little bit harder, just because I did not want to tear the hose on the tub or pump inlet. Make sure both are fully seated or else it could still leak. The drain hose and the clip are pretty self explanatory. I tried to buy a generic drain hose at a big box lumber yard, but I could never make it fit right.

Hope this helps.

all straps were broke due to over loadiing washer

  • Customer: Danny from north kansas city, MO
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

Pump was making grinding noise

  • Customer: Scott from Herrin, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable)
  • 3 of 3 people found this instruction helpful
Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

There was no fabric softener dispenser

  • Customer: Norma from Holiday, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
Opened lid and place on agitator ... finished

drain hose replacement

  • Customer: Henry from Merced, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Put the drain hose clip on (it will take squeezing but the hose will pass through). There will be a groove that whose width spacing is similar to the clip. Once that's on, insert hose and screw in the clip.

Pump was bad

  • Customer: Patrick from Clinton, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 3 of 3 people found this instruction helpful
I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.
All Instructions for the WJRR4170G0WW
61-75 of 363