Models > WHDSR315DAWW > Instructions

WHDSR315DAWW General Electric Washer - Instructions

All installation instructions for WHDSR315DAWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WHDSR315DAWW
31-45 of 486
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

a small metal washer came off putting the machines weight on a plastic piece that shattered

  • Customer: Kevin from Hazelwood MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 13 of 14 people found this instruction helpful
first use a puddy knife to remove the front cover – slide the puddy knife in the front upper left than right corners where the top meets the front of your washer they are push in clips that hold the front cover (they are not easy to damage)
second pull the front out than up of the bottom clips, there is the rods with a tube assembly is either black or yellow that hold the tub up
remove the 2 screws holding the top they are near the clips you used the puddy knife on
lift the lid about 4 inches and you will see how it works, at that point with the replacement part in hand it is self obvious what to do replace the rod.
When done try the washer and if it works, if so put the covers back on.
The shock of it all is watching the natural violence your machine goes through just to wash your clothes

The local repair man ssaid we needed a timer switch for $90.00 plus labor

  • Customer: Marlin from Riverton WY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 13 of 16 people found this instruction helpful
I took the control knob off and saw the teeth broken and got on line and ordered the part. It was an easy fix.

Loud bang during spinning

  • Customer: Jim from Marion MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 12 of 13 people found this instruction helpful
Remove aggitator, disconect 4 support straps, pry off clips/ latches on top of drum. Remove small bolt that holds on the small plastic unit unto trans.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.

Discharge Pump was leaking on our GE Washer

  • Customer: George from Cambridge MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 11 of 11 people found this instruction helpful
Popped the front off the washer by placing a towel under the screwdriver to prevent chipping the paint. Had to spent almost 45 minutes soaking up water that had leaked from pump. Must have been leaking for some time before enough leaked under washer and became visible, because there was a lot of rust build up. (1).Removed old pump by first un-pluging washer and them removing (2) connecting wires from pump. (3).Next use nut driver to loosen flex hose from washer. (not from pump). Loosen spring clamp from discharge hose , and slide up. (4) Using nut driver I removed (2) hex screws that held pump to frame, then removed pump and motor assembly. (5). Mopped up water with large (old) bath towels (6). Used hair dryer to dry area. (7). Used wire brush to brush away surface rust. then used small shop vacuum to remove this surface rust. (8). Used small brush to paint white rust-olem paint on rusted areas, used hair dryer again to help paint to dry, then gave it a second coat and again helped it dry. (9). I then removed flex hose from old pump assembly, checked it for cracks and finding none I attached it to new pump with existing spring clamp. (10). I then put pump assembly back inside washer, but did not attach with hex screws yet. (11). Re-attached the drain hose by sliding the spring clamp back down, making sure it is around the hose and discharge spout. (12). Reattach the flex hose to washer discharge spout. (13). Screw new pump and motor assembly unto newly painted frame. (14). Re-attach (2) wires to pump and motor assembly. (15). Plug washer back in and try filling it with some water, letting it go into the drain cycle to check for leaks. NOTE: You don't have to go through and entire wash cycle. Just use the dial to put some water in then move it to drain and /or spin to get the new pump and motor assembly going. I did this a couple of times and then did an entire load of clothes to ensure there were no leaks. After I was sure there were no leaks, I simply popped the front panel back on. My part cost a total of $64.00 including shipping, and it took me about 1 hour of my time. I checked with my local GE dealer and his cost would have been $98.00 for the part, and $85.00 for labor for a total of $183.00. I AM VERY HAPPY. Oh bye the way I had my part within 3 days of the order and that was with regular shipping. I will always use Parts Select from now on.

Washer agitator not working

  • Customer: Brenda from Coon Rapids MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 12 of 8 people found this instruction helpful
First I removed the agitator with a belt. Then I removed the nut with a wrench. The Agitator coupli was smooth on the inside so I knew that was the problem. I got the new part, slid it into place. Tightened the new bolt and replaced the Agitator component with a quick push downwards. Easy!

washer failed to drain water from machine

  • Customer: Kristy from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 10 of 10 people found this instruction helpful
1) Disconnect power
2)remove front panel
3) remove screws and take hoses off
4) remove & replace water pump
:) YAY. all done

Loud banging noise

  • Customer: Franklin A from Elk Grove CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 11 of 13 people found this instruction helpful
Removed the front cover of the washer by sliding a screw driver to release the clips. Loosened the 4 nuts that held the drivebelt motor pushed the motor back to release the drive belt. Replaced the drive belt, pulled motor until drive belt was snug and tighted the 4 bolts. At the same time, I replaced the 4 tub dampening straps located at the top of the tub and now the unit is just like new.

Tranny oil ran out onto Laundry room floor/making noise

  • Customer: Larry from House Springs MO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 11 of 13 people found this instruction helpful
Removed front cover(use screwdriver)clips on top of cover under lid
Disconnected power from wall
Disconnected wires to motor 1 screw/unplug for motor
Uncwrewed clamp on drain hose
Removed top lifts off easliy
With help released Washing drum assy from hangers
Slid back and Tilted drum assy outwards from drum opening out to the front of machine
Pulled agatator up and off of hub
Remove one bolt from hub 1/4 " rachet w 3/8" socket
Pull off cap
Removed Locking nut(couterclockwise)nut is soft metal used good vice grips firmly locked on nut
Removed inner washing drum
Turned over Entire Assy (motor up)
Removed belt (slid off)
Removed 4 blots from Motor/Tranny assy to Plastic outer drum
Lifted off Motor/Tranny assy and pulled tranny out
Reaasemble in reverse order witht the exception of replacing the hub seal(inside)Outer drum assy.
There were service instruction under the front control panel.

Broken knobs

  • Customer: Ray from South Pasadena FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 19 people found this instruction helpful
Actually putting on a knob is self-explanatory. But wanted to say your company had the best price and reaction (delivery time). Great job by PartSelect!

Agitator not agitating

  • Customer: Troy from Porter TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 11 of 14 people found this instruction helpful
Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.

Excessive agitator side movement

  • Customer: Richard from Spring City PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 11 of 14 people found this instruction helpful
Bought all of the parts to remedy this. It ended up being the top transmission seal/bearing which is not a replaceable part. I could see the shaft moving side to side. But the parts diagrams are not detailed enough to show that when assembled.

She led a good life.

My new side loader is SO MUCH BETTER AND INSANELY EFFICIENT. I highly recommend making the change if you need a transmission..

Transmission bearing went out creating alot of noise on every cycle.

  • Customer: Scott from Littleton CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 10 of 11 people found this instruction helpful
I had to remove top control panel and flip it over the back and out of the way, but did not have to unplug anything. I then had to remove front and top panels in order to remove the agitator and eventually the tub assembly itself. Once the tub assembly was removed, I had to turn it upside down to remove the transmissing and brake assembly as well as the mounting bracket. The entire removal process took about an hour and a half. The reassembly took less than an hour. The most difficult part was removing the 1 11/16 nut that ties the agitator to the tramsmission through the tub. It took 3 of us to hold the tub in place so that one of us could use the 3/4 drive ratchet and extension to loosen the nut. We did the same thing during the reassembly. All together there ware quite a few parts removed and a fair amounte of different screws. In order to perform this job, you must have a decent tool set and the ability to diagnose each step of the process, but it's not very difficult otherwise.

Changed drain hose on GE washing machine

  • Customer: Andres from Stamford CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
I attached the Drain Hose Clip to the Drain Hose Extension and then pushed the drain hose all the way into the drain hole in the back of the machine. I then screwed the clip to the machine. Done. Very painless. Fast delivery... ordered it on Monday, arrived on Tuesday.

Washer machine didn't get water.

  • Customer: Eduardo from Borrego Springs CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
I remove three screws on top of the washer, moved the cover of the machine in order to get access to the water valve, and then desconnected the two solenoid of the valve,and removed two screws that hold the valve with the frame and installed the new valve in same order a took the old one.

There was no hot water coming out, I had already checked the screens

  • Customer: Tricia from Glen Allen VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 9 of 9 people found this instruction helpful
First I removed the old part (2 screws)
Pulled off 4 wires (maybe the wrong word, I'm not a professional!
Put the new part in-turned the water on and had a stream of HOT water-yay
I had been putting this off because no one in my family had noticed (except me) and with my husband out of work it seemed like a low priority, but when my daughters came home for Christmas, they said "There's no hot water in the washing machine" so I took the plunge--I cannot believe I waited that long!
It literally took me seven minutes!
All Instructions for the WHDSR315DAWW
31-45 of 486