Models > WGR211ES1 > Instructions

WGR211ES1 Westinghouse Dryer - Instructions

All installation instructions for WGR211ES1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WGR211ES1
301-315 of 339
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Constant high pitch squeaking

  • Customer: Courtney from Washington IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took out drum which was the hardest part because Im short so I needed a little man power to lift it up then out.... Replaced entire bearing parts and belt.... You do need a nut driver for that but we ended up using plyers which worked okay.... All in all it was way easier than I thought it was gping to be.... Now it sounds brand new.

No heat

  • Customer: THOMAS from VINELAND NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Taking the front of the dryer off was rather easy. A two screws under the control panel and once the flap that separates the washer and dryer was removed there are 4 more screws to remove and release the control panel (disconnect wire harness and let panel hang). Once removed, two more screws separate the door/front of the dryer. Remove those and the 4 on the top front of the dryer. When completed the only restriction you have are bracket mounts. Just give a good tug and the front should separate from the body. Thereafter, the drum can be removed by removing the belt first. Reach to the back and depress the spring loaded pully by moving it to the right, releasing the belt. Let the belt hang while you unscrew the the drum screws, 3 located in a triangle pattern inside the drum. Remove them and the drum from out of the dryer. Straight ahead of you is the heater assembly. In my case, only the coil had to b replaced. So it was as simple as removing the old and in with the new. Reverse your disassembly to get reassembly.

Dryer was making a loud squeaking noise

  • Customer: Michael from Drums PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Installed a new rear drum bearing kit and new drum belt

Rear drum bearing worn out

  • Customer: jack from Post Falls ID
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Basically followed the You tube videos on standard, stand alone dryers as mine is a stack-able unit. Allow a lot of room to work. Unplug electricity and or the gas, vent hose and water hoses. Start removing screws as per the video, remove Belt then lift up then out the dryer drum. (The drum drops in from above on the back of the unit)the rest is remove and replace as you go. *TIP... I use my phone to photograph tricky areas so I can review as needed. It was more scary then difficult. You can do it!

Broken plastic door handle

  • Customer: Clifford from Petaluma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snapped on the new one.

Loud squeaky noise

  • Customer: Alexander from GREECE NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My dryer was making a horrible squeaking noise comparable to nails on a chalkboard! I looked to get a similar used replacement because I was in a bit of a pinch for $$$, after being frustrated and not finding anything I came here and found all the parts I needed for my repair for UNDER $40!!!! I followed the super easy how to video that was provided on this website. This is the second repair I have made to this dryer, I did the heating element about a year ago. I also used this site to purchase the part and used the how to video associated with that repair. I was very surprised that I received the part the next day when I paid for regular standard shipping! Overall this was a an awesome experience and I have saved so much money repairing my dryer on my own vice paying someone to do it!!!

Timer Knob broke

  • Customer: Kisha from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just slid the new timer knob on the dryer and we were all set. Super Fast shipping and easy to replace. Thanks so much!

dryer was making a shrill noise

  • Customer: Mike from Goldonna LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the front then removed the belt that turns the drum pulled the drum strait up from the top then removed the bushing from the back wall put the new one in I also put A little grease in the new bushing to keep it from wearing installed the drum and front. realy easy. I'm A Instructor at A technical collage in Winnfield Louisiana and I used this as A project for my students.

drum belt

  • Customer: MANUEL from SAN JACINTO CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
so easy my daughter installed it the video was very helpful

timmer knob broke

  • Customer: Sharon from Hampton VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
knob was delivered and i just put it on and it worked. very easy and less expensive than a service call.

Loud screeching noise, barrel turned OK and Heater worked

  • Customer: Ellen from Willits CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I took the lower back panel off. Loosened the center bolt and took off the old Idler pulley. It looked brown in the middle and didn't roll well. But I wasn't sure if that was it, because the noise was so loud and sounded metal on metal. So I checked everything and vacuumed everything. After I got the new part it took me about 5 minutes to put the new one on. And dryer works fine. Thanks for the quick response and I saved about $200.00!

Timer Knob broke.

  • Customer: Sherry from Olympia WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I simply pushed the knob back onto the post. No problem! Now I don't need pliers to turn my dryer on. Yippee! (And the part was cheap-less than $10.00).

replaced rear drum bearing

  • Customer: chuck from carroll NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint

My dryers was making a loud thumping sound. Like it was off balance.

  • Customer: Dennis from Maple Shade NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I Took the front off and saw the cushion was gone around the drum and glids were worn down. I ordered both parts . It took 5 minutes to glue the cushion back on around the drum and 2 minutes to snap the drum glids on.But what I couldnt believe was the amount of lint that was all over the inside of the dryer.I would suggest to anyone to take the dryer front off once a year and clean it all out . I now understand fully why there are dryer fires.But the fix was cake and it runs like new.

The Knob Broke Years Ago

  • Customer: Robert from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I finally found this great website that not only had the part, but directions on how to do the work. The part came to my house in about 4 days. After 9 years of being broken, it is refreshing to have it fixed. I have bookmarked this site for ANY future repairs.
All Instructions for the WGR211ES1
301-315 of 339