Models > WGF350ESE > Instructions

WGF350ESE Westinghouse Range - Instructions

All installation instructions for WGF350ESE parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WGF350ESE
1-15 of 29
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn't heat - broiler and burners worked fine-Bake Burner Igniter didn't work

  • Customer: Debbie from Rockford MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 69 of 84 people found this instruction helpful
It was the week before Thanksgiving and we didn't know what to do without an oven. I did some research on Google and of all the websites out there, I found a decent price here at Parts Select and ordered it on Friday. I was shocked when FEDEX pulled up to the door on Saturday afternoon. I went online to youtube and found a step by step video specifically for this part. It's posted by the Repair Clinic. http://www.youtube.com/watch?v=cLxKoF16gac. I was able to fix the part and probably saved at least $150.00 for a service call and repair time. The part cost about $90 and I was done in less than 15 minutes. We just got this stove about 2 years ago and I'm thinking maybe we could have saved my old stove since it had the same problem. Great job Parts Select - I got just what I needed and saved a ton of money in the process. Thanks also for their great informative video online. We had a great Thanksgiving and were very thankful for all our hot food fresh from the oven.

Stove was set up for natural gas and needed to be converted to LP

  • Customer: Ed from Orange TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 62 of 98 people found this instruction helpful
The LP conversion kit contained very good, detailed instructions. I replaced the gas orifices, took off the bottom door and adjusted the regulator.

Used the screwdriver to adjust the low flame and everything was done.

Bought a new gas oven that did not come with a propane conversion kit.

  • Customer: Denny from Bishop CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench set
  • 56 of 80 people found this instruction helpful
I followed the simple instructions that were included in the kit. I started by replacing the 5 orifices on the top burners. The orifices are well labeled with numbers and colors. Next, I tightened the broiler burner orifice and the oven burner orifice with a 1/2 inch wrench. I had to tighten them pretty good to get the flame down where it is supposed to be. Then, I checked for leaks and I was then ready to cook.

Oven wouldn't operated. Error code F9

  • Customer: Richard from Centennial CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 18 of 21 people found this instruction helpful
I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet metal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.

anti-tip bracket not installed

  • Customer: Brian from Panama City Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 14 people found this instruction helpful
I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

oven bottom had foil stuck on it would not come off

  • Customer: ronald from brownsburg IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
First I removed the two screws that hold the bottom panel I then pulled the panel out and put the new panle in and put the two screws back in

Regulator had propane leak past diaphragm

  • Customer: Albern from Bainbridge IS. WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench set
  • 7 of 11 people found this instruction helpful
removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.

burnt in aluminum foil...unable to remove

  • Customer: Michael from Lamoni IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
took the two screws out by hand, slipped out the ruined panel, slid the new one in place, replaced the two screws...simple as that

bottom oven plate had foil stuck to it

  • Customer: Wilma from Syracuse NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Very easy to order,part was delivered promptly and installation was easy.I unscrewed a few screws and lifted the bottom panel out and put the new one in.

Rusted leveling foot

  • Customer: Melinda from Three Rivers MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 1 of 3 people found this instruction helpful
I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

The bolts holding the readburner were rusted and broke

  • Customer: Neeru from Princeton NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 3 people found this instruction helpful
The range top had to be taken off along with the front panel to get access to the place the burner pipe connects. It took more time to unassemble and assemble the range than repacing the burner. The only issue was that the burner was sent without the bolts that will hold it in place so I had to go to local hardware store to get appropriate bolts.

burner ingnighter would not lite burner

  • Customer: Wayne from Palestine IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 14 of 46 people found this instruction helpful
Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.

MEN SHOULD NOT USE THE OVEN

  • Customer: David from Suttons Bay MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
DELIVERY WAS FAST. TWO SCREWS TO REMOVE THE OLD OVEN PANEL. SLIPPED IN THE NEW PANEL AND TIGHTENED THE SCREWS WITH MY FINGERS. JOB COMPLETED. IT WAS AS EASY AS THAT.

bake burner igniter open circuit--no oven heat

  • Customer: Earl from Trinidad CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I followed the you tube www.partselect.com. Got door off--easy, and other parts off--easy, as you tube shows--I used the adj wrench to remove old screws--there are two--front one off--easy, the rear one was stripped at factory installation--so got it out, but broke it off in the process. So I had to drill out the part of the screw that remained, and then used a substitute screw (8-32x1/2) on re-assembly. Re-assembly went easy--note that the removal of electrical connection is a "pinch-squeeze" to pull off.

no heat

  • Customer: John M. from PLEASANT PRAIRIE WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced the oven probe because a no heat problem. also had to replace the oven control. That was a bit expensive but still saved me hundreds not calling a serviceman. By the way, it works like new.....
All Instructions for the WGF350ESE
1-15 of 29