WGD9550WL1 Whirlpool Dryer - Instructions

i replaced the two sensors in the heating element which were very clear in your diagram and it worked perfectly

Checked voltage coming into unit, good. Checked schematic and traced the voltage through the safeties and interlocks. Found the problem at the thermal link. Isolated unit from all voltage sources. Removed part and ohmed the resistance. Found it open. Ordered new link and it arrived before schedule. Replaced and connected wiring, returned power and tested. Worked great! Very easy to find and repair!

changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.

Replacing the filter was easy - the new filtes's seal seems much more secure. The new one works much better than the old one.

Got online with parts select, easily found the parts needed and ordered them. They arrived very quickly. The repair itself took all of 5 minutes and now the dryer door stays shut like it is supposed to. Only complaint is shipping was more than the parts but then again, I didn't waste a lot of time running all over town looking for what I needed. So, in the long run I saved money , especially when compared to a calling someone else to fix it.(big bucks for even the most minor service call as you all know).

My husband changed the idler pulley. It took him 5 min. Thank you sooooooooooo much. Saved us 1000.00 dollars. He wanted to by a new one but investigated the problem on line. He is a handyman and was just being lazy. I ordered the part and he fixed it. I love saving money!!!!!!!!!!!!! And I love my husband!!!!!!!!!!!!!!

pop off put in done

It was a fairly simple repair to perform with the dryer in place. I simply opened the bottom/front access panel to start, the door removes if you pull up after opening. Then I disconnected the two and three wire connector to the two coils. Next I removed the bracket screws that fasten the coils to the valve assembly. This was a little difficult with the screw closest, because of the small clearance and #1 sized phillips(stubby would work well.) The rear screw I managed to remove by using both a small flathead screwdriver(hex shaped shaft) and an adjustable cresent wrench. At this point, it was a simple matter of installing the new coils and the bracket, and then reconnecting the two plugs. It almost made me want to do laundry.

Removed power cord. Removed screws in back cover. Checked electrical diagram. Found fuse, checked. New part arrived promptly on time. Was correct part. Tested before instalation. removed one screw that held fuse. unpluged the two wires. Repluged wires, reinstalled screw.on new fuse, replaced back cover and screws. recoupled power, tested. ran perfect.

I removed the back of the dryer (after unplugging and shutting off the gas valve) I vacuumed any fuzz and debris. I also removed the dryer vent and cleaned that too. I unscrewed the thermal fuse and replaced it with the new one. I wiped everything down and replaced the back and ran the dryer and it worked! Thanks for your help and for saving me money! My husband was so glad we didn't have to call a service man we celebrated by going out to dinner!

Took out the old one and put in the new one.

I thought that I was going to have to buy a new dryer or rather a used one to replace my dryer when it stopped heating. I knew I could not afford an appliance repair person to come out to the house, so I searched for my appliance on the internet for repair parts. Your website helped me to figure out the part that I needed to replace; i.e. the thermal fuse for $9. Since you advertised that you took return parts, I placed my order. Without any hassle short of the obvious moving the dryer away from the wall and removing the back panel I was able to do this in a short time. I was so excited to realize that my dryer was heating up. Thank you.

I removed the back panel from back of dryer, unplugged the thermal fuse as shown in YouTube instructional video. Put back panel back on, plugged in dryer. Started workimf right away. Could not have been easier! The whole process from troubleshooting the problem to oderimg and installing the part was surprisingly easy. Thanks so much! Best service I have gotten in  a long time.

Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.

Downloaded a schematic of the dryer controls. Watched a UTUBE video of how to remove the front panel of a Maytag Performa dryer. It was pretty easy. Consulted your website and found out that bad coils are typical of the symptoms 46% of the time. I have bought parts from you before and happy with results.