WGD9450WR0 Whirlpool Dryer - Instructions

Watched steve on the video on changing the thermistor a couple times, it appeared to be straight forward replacement. Unplugged the dryer. . . Went through the front, my lent filter slides in and out from the lid so I had too remove two extra screws to detach it. After opening up the front it became very apparent my thermistor was not located in the same location as the one in the video. Dryer needed a cleaning (lint/dust) so I released the idler pully tension on the drum belt and went ahead and removed the drum/belt and shop vac/ blew with compressed air and shop vac once again. Gave my dryer a much needed cleaning since I had it apart. Put everything back together in about 20 mins. Pulled the dryer away from the wall and removed rear cover and presto there it was right next to the dryer air outlet. Replaced thermistor and replaced back cover, inspected out flex hose on dryer outlet, I clean it out (flex) yearly to prevent problems. Reattached flex on both ends, re-positioned dryer, plugged back in, and works great! Definitely fixed my problem. . . Replacing the drum by myself was a bit difficult. Still do able (there's a video on that also. . )

My front- loading dryer is 4 years old and lint screen felt liner never lasted long without falling out. When I received my Part Select I knew the quality surpasses manufacture screen. It is so much better and we are your new customers forever Thank you Cheryl

Unplug appliance from power source. Started by simply using screwdriver or steel putty knife to snap up the top corners of the top section of the dryer. It swings open like the hood of a auto. Looked on the back side of the front panel and found small 5/16" bolts on either side. Removed these bolts and lifted up on the front panel to remove the panel. Slide panel out of the way far enough to access the coil kit on the lower front section of the dryer. (The wires going to the door control switch will allow this without unplugging.) May need a helper to hold the dryer drum up out of the way or prop it up as I did with a block of wood so you can easily unplug/re attach the coil wiring. There are two Phillips head screws that hold the coil keeper in place. Remove these two screws, unplug the two coils (front coil has a three connector plug and the one behind it has a two wore plug). the front coil has a small sleeve that I needed to transfer to the new coil in front. Inserted sleeve as it came out of the old coil, slid both coils back in place, replaced coil retainer being careful to line tabs on top of coils so that they lined up in the coil keeper. Replaced screws in coil keeper. Placed front panel back on being careful not to damage the felt liner that the drum spins on. Replaced the two bolts on the inner side of each corner of the front panel. Lowered the top panel and firmly pushed it back down so that the holders went in place. Plugged it up and it worked perfectly.

It was really easy. First we watched a Youtube video about gas dryers that wouldn't heat, and then we did exactly what the guy recommended on the video -- try to see if the igniter lit (it didn't), but then he recommended we check the thermostat and some other fuses. So, like he recommended, we removed the back, checked the thermostat, etc. We initially bought the wrong part, but when we got the right one, it took less than 15 minutes to get it in and working. It was a snap. Just had to remove a few screws, unplug the old igniter, plug in the new igniter, and put in the few screws that held it in place. EASY!!

This repair is very simple. (1) remove the lint screen bracket on top - two phillips head screws. (2) Gently pry open the top of the dryer with a large flat head screwdriver. It hinges backward. (3) Remove the top two nuts on the front panel. Lift the panel upward off the lower brackets. The door wiring is still connected, so I just rotated the front panel to the side. The interior is now exposed. (4) Take the drum belt off the tensioner assembly and pull the drum out. (5) Remove the coil retention plate - two phillips screws. (6) Disconnect the old coils, install new coils. I started the dryer up while disassembled to ensure the new coils worked and the burner fired. But a word of caution ... don't run the burner long with the dryer apart, as it could overheat. After all of this, reverse the process. YouTube also has a couple good videos showing all of this visually. I have very average mechanical skills, and this was an easy job. Another word of caution: most of the metal surfaces inside the dryer have nice sharp edges. Invest in a good pair of gloves to avoid mincing your hands up.

First of all, Parts Select is a great service. By giving us an idea of what parts we needed we were able to buy them without a lot of expense. My son and I did this repair together, and it took us a long time. We found an excellent video for repair on the web, and then lost it and couldn't find it again. We had trouble even getting the dryer opened up. That is where a putty knife comes in handy. Be sure to find out how to open it; it will save you a lot of grief. It is supposed to be easy, but it wasn't. Still,it was great to get it fixed so inexpensively. I'll leave the "how I did it" part up to people who had an easier time, but no regrets that we did it. Parts select sent the parts right away.We ended up only using the coil kit.

flame sensor was a little tricky since a wrench was necessary since there was no clearance buy pretty simple put back plug in started still no heat after 6 min running time . now it coil kit so simple was surprised change out both and put cover back on plug in started and been drying ever since thanks for all your help

Removed back panel and tested all components. Everything was good so had to remove front to test last 2 components. Removed front and used brick (handy tool when your working solo) to hold drum up and in place (with full load of damp towels). Defective igniter. Testing all took 10 minutes, replacement took 2. Spent more time opening and putting machine back together than testing and replacement took.

UNPLUG UNIT FIRST!!! Removed back cover. Make sure to note not all screws hold the back cover by closely observing the screw. Take a picture of the belt routing before removing from the idler pulley. Use headlamp or flashlight to light up pulley area. Remove belt from idler pulley by pushing idler assembly towards the right. Use small screwdriver to remove the existing pulley by prying off the existing tri-ring from the back of the pulley. You may have to "feel" the ring since it in facing away from you. Once tri-ring is removed, slide off old pulley and gasket or old second tri-ring. Replace with gasket first, then pulley then tri-ring. Reroute belt. Use picture if needed. Replace back cover.

Followed videos seen on the internet for my dryer's repair. Went exactly as shown.

pull out lint screen, removed 2 screws. lifted top up. removed 2 screws from the front,disconnected wiring harness. removed the drum and belt. located and removed the igniter, sensor, and coil valves. replaced all with new parts. reassembled. now it heats up. i believe that i only needed the coil valves. coil valves not shown on parts list, i purchased later. everything was very accessible with the drum removed.

Just took the old one out and slipped the new one in! That's it! That easy. Thank you!

I highly recommend the videos on this site for repair information. It wasn't exact for the age/model of my dryer but very close. Remove the top panel and then the control panel. Remove the lower front panel and finally the door and main front panel. Unloop the belt from the motor and remove the drum. I found one of the drum rollers was bad, which was causing my problem, but I replace all 4 rollers, the belt, and the idler wheel. Sounds like it did when it was new! Find the video for your model and watch it!!

It was all put together... I just switched them!

Ordered thermal fuse and cycling thermostat