Models > WGD9400SZ0

WGD9400SZ0 Whirlpool Dryer - Overview

Get Parts and Repair Help for WGD9400SZ0

If you know the dryer repair part you need, you can browse the list of all parts on the WGD9400SZ0, or you can search by name or part description. You can also find your part by where it is located on the WGD9400SZ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for WGD9400SZ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$13.95

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil.

$4.06

Door Catch Kit

This dryer door latch kit comes with one plastic door latch and one metal door strike.

$24.54

Lint Filter

This filter collects lint as it passes through the dryer vent.

$22.75

Igniter Kit

This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is used for many gas clothes dryers.

$25.66

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

$16.63

Idler Pulley with Tri-Ring and Gasket

A dryer's idler pulley helps the belt to rotate the drum. Also known as dryer belt tension pulley wheel.

$22.73

Internal-Bias Thermistor

Part may differ in appearance, but functions the same as original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

$4.46

Thrust Washer

$38.92

Dryer Repair Kit

This kit comes with one multi rib belt, four drum support rollers, one idler assembly, nine tri rings and one washer.

$3.46

Leveling Foot

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door Catch part had fallen out,/ was missing

  • Customer: Terri from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 483 of 486 people found this instruction helpful
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source. read more

Dryer ran but would not heat

  • Customer: Gary from Haverhill NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 190 of 215 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more

Door wouldn't latch.

  • Customer: Melody from North Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 148 of 219 people found this instruction helpful
I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!! read more