Models > WFW9500TC01

WFW9500TC01 Whirlpool Washer - Overview

Get Parts and Repair Help for WFW9500TC01

If you know the washer repair part you need, you can browse the list of all parts on the WFW9500TC01, or you can search by name or part description. You can also find your part by where it is located on the WFW9500TC01 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$82.92

Bellow

This part is also called the Door Boot Seal. It's the main seal between the front bulkhead and the outer tub. Clamps are not included. Must order clamps separately, if needed.

$24.30

Drum Baffle

Sold individually. This part moves the clothes around inside your dryer/washer and helps to direct the flow of hot air during the drying cycle.

$139.85

Drain Pump Kit

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.

$91.79

Door Hinge

Used with front load washers.

$13.64

Bellow to Outer Tub Clamp

Used to help hold your bellow in place on your washer.

$4.95

Touch-Up Paint - White

$14.54

Bellow Clamp

This is used to help hold the bellow in place.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.70

Hose Clamp

This hose clamp is sold individually.

$39.45

Flowmeter

This part continually measures the amount of water entering the tub. It will make adjustments if too much or too little water is present.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bellows were moldy, needed to replace

  • Customer: Franck from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 214 of 230 people found this instruction helpful
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached... read more

Washer would not drain ,F02 and SUD code displaying

  • Customer: Donald from Wichita KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 106 of 110 people found this instruction helpful
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the p... read more

The washer kept giving a 'suds' error or an F35 error and would not progress through any of the wash cycles. It would partially fill with water, just enough to dampen some of the clothes, and then show the error message.

  • Customer: Susan from Hatfield PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 65 of 70 people found this instruction helpful
I removed the 3 screws toward the top of the back of the washer to remove the top. After that, I located the water pressure level switch, slid it out of the slot into which it is secured, removed the narrow black tubing from the bottom of it, and draped the newly-unattached end of the tube so that it would be easy to find. Then I removed the set of wires ... read more