Models > WFW9200SQ00 > Instructions

WFW9200SQ00 Whirlpool Washer - Instructions

All installation instructions for WFW9200SQ00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WFW9200SQ00
46-60 of 131
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The water didn't drain, so the drum wouldn't spin

  • Customer: Jill from New Rochelle NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.

Tub would not drain even though pump was running

  • Customer: Steve from Cary NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
Remove three screws holding the lower panel, the pump is right up front. Probably the hardest part was holding the hose clamps open while attaching the hoses to the pump housing. One screw holds the pump assembly in place. Hold the over-ride switch closed, check for leaks, and replace the loser panel.

Pump not draining the water out.

  • Customer: Martin from Kotzebue AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.

Baffle was worn out/broken

  • Customer: Day from Basking Ridge NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
No instructions needed. Very easy to replace. You guys are great! Much cheaper than others and delivered next day! You are now on my "favorites"!

error F28 in mid cycle

  • Customer: Nicholas from Boothwyn PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
check error code : no water flow
pulled hoses [hot& cold] to clean screen in line.
pulled flow meter out from under top of hood to clean and check free wheel movement inside.
still error code F28 in mid wash cycle. called in and talk with service: he explained that hot& cold water valve was opening to slow or not enough for flow meter to read full presure. I replace water valve and flow meter. washer is doing fine. [I was getting readly to go in futher down the line and get new controler. talking to service stop me from spending a lot of money. THANK YOU

F-20 ERROR CODE

  • Customer: GARY from CLARKSVILLE IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 5 people found this instruction helpful
TAKE OFF TOP OF WASHER AND THE FLOWMETER IS IN THE BACK LEFTHAND CORNER ON THE TOP OF THE WASHER.REPLACED THE WATER LEVEL SWITCH ON THE TOP RIGHTHAND OF THE MACHINE ALSO. GOT ABOUT 150.00 TOTAL INVESTED W/SERVICE CALL FROM LOCAL TECH.F-20 HAS NOT CAME BACK YET. I HOPED IT FIXED IT WASHER IS ONLY 3 YRS. OLD. -GD

Plastic retainer ears broke

  • Customer: Avis from Abingdon, VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Took old broken part off and replaced with new. Involved removing 2 screws and putting back.easy repair. Biggest problem was length of time it took part to arrive.

baffle connectors worn off

  • Customer: richard from chetek WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
Placed baffle inside of washer and pulled to lock into place. EASY!!!

Pump not working

  • Customer: Darrell from Lady Lake FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Replaced pump

Shaft in water pump broke

  • Customer: Jeffrey from Adrian MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 2 of 2 people found this instruction helpful
I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.

Leaked water

  • Customer: Valerie from Huxley IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 3 of 6 people found this instruction helpful
simple repair. After reading other reviews my husband was confident he too could do the repair. He was right, we were so very glad not to have had to call for service.

front door leaking

  • Customer: jim from winchester VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.

Displayed F and H alternately

  • Customer: LAVERNE from NIANTIC CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem

Replace Bellows between door and tub

  • Customer: Gerald from Douglas AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 7 people found this instruction helpful
Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip

wont pump the water out

  • Customer: Paul from Corning NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together
All Instructions for the WFW9200SQ00
46-60 of 131