WFU14K2BW1 Westinghouse Freezer - Instructions

its best to use power screw driver lot of screws .took out all screws took off door took out side to remove ice from door. just used water to melt ice. took off old gasket and put on new gasket. put door in place and started screws in four coners do not tighten screws at this point.put in rest of screws. work arondclock wise making sure gasket is seated while tighing screws. check gasket for flatness you may have to use hair dryer on gasket to make it flat.

Simply unscrew panel but do not remove it. Remove old gasket. Fit new gasket between panel and door. Fasten screws and no more leaks and better temperature contol. This was so easy and rejuvenated my freezer. Thank you for quick shipment, great service, easy to navigate website, and fast phone help. I highly recommend your company. good luck with your repairs that you can do, as I have zero mechanical ability and did it !!!!

Removed old cold temperature control; tested with ohm meter and determined that the control was bad; ordered new cold control from PartSelect.com. Installed new cold temperature control with no problems; freezer is now running like new again!
p.s. I was very pleased with how fast I received my order from PartSelect.com!

Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.

removed door and took all the screws out of the inside door rack. removed old door seal . replaced door seal and made sure that the seal fit around and door rack fit into the groove then replaced all screws and tightened choosing random sections to tighten .replaced the door plugged back in wires that I removed and replaced door hinge screws . Shut door and checked sealing 2 hours later .Complete seal .

Loosen screws, removed old gasket seal, replace with new gasket (nice to use 2 sets of hands) and re screwed. Used hairdryer to heat up and fluff out a spot that wasnt seal all the way. Pretty simplementation to do.

Unscrew all the fasteners from the door inner cover from the bottom to top to hold it in position, got rid of the old gasket.

I Cleaned all and install the new gastket into the door inner cover. then reintalled cover to the starting from the top to bottom to hold it in place.

this is a one man job but with two will be easer

Removed old gasket, then installed new gasket. Make sure to allow new gasket to set out for a few days prior to installing to get all wrinkles out, use a heat gun after installing to make gasket shape to freezer door.

Put the new temperature control unit in plugged freezer back in and immediately turned on. Very simple repair. Saved a lot of money not having to purchase new or call a repair shop.

Needed to remove both left and right broken (plastic) supports and reinsert the new parts. Not hard at all...worked like a charm!

Removed old gasket by backing out screws around inner door panel. I did not remove the screws just loosened in order to remove old gasket. Starting from the top of the inner door panel I set the old gasket and squared off. Tightened top screws and worked the gasket in on the sides and tightened several of the screws on the sides then set the bottom of gasket in the door. Inserting the gasket in the bottom was the hardest part of the job. The overall job took less time than expected.

A 1,2,3 approach: 1, order the right part at the best price, Part Select has easy to navigate website and provides updated info on what will work in your appliance at a fraction of other site costs. 2. Configure the appliance to control the temp for a few days to save the food. This is accomplished by jumpering the two control wires to keep the compressor on and plugging the appliance cord into a timer with a 2hr on and 4hr off cycle. use the thermometer verify 0 degrees. 3. When the temp control is delivered unplug the power cord and proceed to repace the temp control, using care not to crimp the temp sensor bulb tubing. A #1 phillips screwdriver will release the control housing and temp sensor clamp assy. When complete set control to mid range and plug appliance into wall outlet. Use thermometer to set desired temp.

The installation was really simple, no problem. No instructions needed. What surprised me was, The new thermostat was installed in less then 24 hours after it was ordered. I live in FL

Pulled the freezer out and unscrewed the screws around door. Gasket slide right out. After placing the new gasket, I used a hair dryer and sealed the gasket tighter. Works like a charm!! Very pleased with this do-it-yourself fix.